Products
Categories
- Main categories
-
- 3D PRINTING
- ACADEMIC OFFER
- ARDUINO
- AUTOMATION
- BOOKS
- DIY KITS
- AVT kits
- Audio
- Car
- Chargers
- Clocks, timers and schedule switches
- Communication
- Converters
- Development kits and modules
- Displays
- Electronic games
- Generators
- Hobbies and fun
- House
- Interfaces
- Light effects
- meters
- PC
- Power Supplies
- Pre-programmed circuits
- Printed circuit boards (PCB)
- Programmers
- Regulators, controllers
- Remote control
- Starter sets Ośla Łączka
- Starting sets for beginners
- Workshop tools
- Audio
- Other sets
- TOP-Q kits
- Totem
- UGears
- Velleman
- AVT kits
- EBOOKS
- ELECTRONICS
- Cables
- Cameras and accessories
- Communication
- Conductive materials
- Connectors
- ARK connectors (Terminal Block)
- Coaxial connectors (RF)
- Connectors
- Crocodile clip
- D-Sub drawer connectors
- DC power connectors
- FFC/FPC ZIF connectors
- Goldpin connectors
- IDC connectors
- JACK connectors
- JST connectors
- Jumpers
- Memory cards slots
- Other connectors
- Pogo pin
- RJ45 sockets
- Slip ring connector
- Supports
- Szybkozłącza
- USB connectors
- Cooling
- Displays
- Electronic modules
- A/D and D/A converters
- Audio
- Barcode readers
- CAN converters
- Converters USB - UART / RS232
- Data logger
- DDS/PLL generators
- Digital potentiometers
- Encoders
- Expanders of the I/O
- Fingerprint readers
- HMI modules
- Image and video
- JTAG accessories
- Keyboards, buttons
- LED drivers
- Memory card readers
- Memory modules
- Modules with power outputs
- Motor controllers
- Power modules
- RS485 converters
- RTC modules
- Servo Controllers
- TSOP infrared receivers
- USB Converters - I2C / 1-Wire / SPI
- Voltage converters
- Gadgets
- GPS
- Intelligent clothes
- LED - diodes, displays, stripes
- Luminous wires and accessories
- Memory cards and other data storages
- Passive elements
- PC accessories
- Printers
- Prototype boards
- Semiconductors
- A/C converters (ADC)
- Analog systems
- Audio systems
- Bridge rectifiers
- Button
- D/A Converters (DAC)
- DDS synthesizers
- Digital circuits
- Diodes
- Drivers of motors
- DSP microprocessors
- Energy counters
- Energy harvesting
- ESD security
- IGBT drivers and bridges
- Interface systems
- LED drivers
- Logic converters
- Memory
- Microcontrollers
- Optotriacs and optocouplers
- Other
- PLL generators
- Power systems
- Programmable systems
- Resetting systems
- RF systems
- RTC systems
- Sensors
- SoC systems
- Timery
- Touch sensors
- Transistors
- Sensors
- Accelerometers
- Air humidity sensors
- Air quality sensors
- Current sensors
- Distance sensors
- Flow sensors
- Gas sensors
- Gyroscopes
- Hall sensors
- Humidity sensors
- Infrared sensors
- Light and color sensors
- Liquid level sensors
- Magnetic sensors (compasses)
- Medical sensors
- Motion sensors
- PH sensors
- Position sensors
- Pressure sensors
- Pressure sensors
- Reflection sensors
- Sensors 6DOF/9DOF/10DOF
- Sensors of liquid quality
- Temperature sensors
- Vibration sensors
- Sound transducers
- Switches and buttons
- Cables
- INTERNET OF THINGS (IoT)
- MECHANICS
- POWER
- R/C MODELLING
- RASPBERRY PI
- Accessories for Raspberry Pi
- Audio video cables for Raspberry Pi
- Case Raspberry Pi
- Cooling for Raspberry Pi
- Displays for Raspberry Pi
- Extension modules for Raspberry Pi
- Memory cards for Raspberry Pi
- Power for Raspberry Pi
- Raspberry Pi 3 model A+
- Raspberry Pi 3 model B
- Raspberry Pi 3 model B+
- Raspberry Pi 4 model B
- Raspberry Pi 400
- Raspberry Pi 5
- Raspberry Pi cameras
- Raspberry Pi Compute Module
- Raspberry Pi model A/ B+/2
- Raspberry Pi Pico
- Raspberry Pi prototyping
- Raspberry Pi Zero
- Raspberry Pi Zero 2 W
- RETIRED PRODUCTS
- ROBOTICS
- SALE
- SOFTWARE
- STARTER KITS, PROGRAMMERS, MODULES
- Alchitry FPGA
- Altera FPGA
- Analog electronics
- Atmel SAM
- Atmel Xplain
- AVR
- Banana Pi
- BeagleBone
- chipKIT
- Coral
- CPLD Xilinx
- Cubieboard
- DFRobot FireBeetle
- Feather
- Freedom (Kinetis)
- FriendlyELEC
- HummingBoard
- Intelligent clothes
- Kit with a book
- LattePanda
- LPC (NXP)
- M5Stack
- Micro:bit
- Nvidia Jetson
- Odroid
- ODYSSEY
- Orange Pi
- Other development kits
- Peripheral modules
- PIC
- Raisonance
- Raspberry Pi RP2040
- RFID
- RISC-V
- SBC Embest
- SBC MYIR
- SBC others
- SBC UDOO
- Segger programmers
- SoMLabs
- Sparkfun MicroMod
- STM32
- STM32 Discovery
- STM32 MP1
- STM32 Nucleo boards
- STM8
- Teensy
- Universal programmers
- WRTNode
- Xilinx FPGAs
- WORKSHOP
- Adhesives and gluers
- Anti-static mats (ESD)
- Chemistry
- CNC milling machines
- Crimping tools
- Dispensing needles
- Drills
- Files
- Generators
- Handles, magnifiers
- Heat-shrink tubing
- Insulation strippers
- Keys
- Knives and scissors
- Laboratory power supplies
- Laminates
- Measuring devices
- Mikroskopy
- Mini drills and grindrers
- Organizers
- Oscilloscopes and accessories
- Pliers and pincers
- Riveting tools and rivets
- Screwdrivers
- SMD Accessories
- Soldering
- Tapes (aluminum, kapton, copper, insulating)
- Tweezers
- Ultrasonic cleaners
- Vices
- 3D PRINTING
New products
New products
zł5.64 tax excl.
Pololu Carrier for Sharp GP2Y0D810Z0F and GP2Y0D805Z0F Sensors
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Pololu Carrier for Sharp GP2Y0D810Z0F and GP2Y0D805Z0F Sensors
This tiny carrier board makes it easy to integrate the Sharp GP2Y0D810Z0F and GP2Y0D805Z0F digital distance sensors into your project by providing all of the required external components, an LED for feedback about the output state, and 0.1"-pitch, three-pin interface to the sensor.
Overview
The GP2Y0D805 and GP2Y0D810 are Sharp’s smallest and fastest distance sensors, and our tiny carrier board for these sensors includes all of the external components required to make them work. With a sample rate of almost 400 Hz and a sensing distance to 5 cm (GP2Y0D805) or 10 cm (GP2Y0D810), this sensor provides an attractive alternative to shorter-range LED-phototransistor reflectance pairs and longer-range but slower sensors such as the Sharp GP2Y0A21YK0F analog distance sensor.
However, these sensors require external components and have a non-standard 1.5 mm pitch, which can make them difficult to integrate into projects based on a 0.1" pitch. This carrier board includes these components and provides a 0.1"-pitch, three-pin interface: ground, power, and output.
Note: this product requires a Sharp GP2Y0D810Z0F or GP2Y0D805Z0F sensor (sold separately). We also offer a version of this carrier board assembled with a GP2Y0D810Z0F and a version assembled with a GP2Y0D805Z0F.
Using the Carrier Board
Pololu carrier with Sharp GP2Y0D810Z0F digital distance sensor 10cm. |
---|
You will need to solder the sensor to the carrier board so that the solder connections are made on the component-side of the board and the sensor package presses against the component-free side of the board. Once the sensor is soldered in, the Pololu carrier board lets you interface with the GP2Y0D810 or GP2Y0D805 sensor using a three-pin 0.100" connector, such as the included 3×1 straight male header strip and 3×1 right-angle male header strip. You can connect to these pins with a servo cable or with a custom-made cable using pre-crimped wires and a 3×1 crimp connector housing.
The square pad is ground, the middle pad is VIN (2.7 – 6.2 V), and the remaining pad is the sensor output, OUT. Depending on your power source, you might notice an increase in performance by placing a large (>10 uF) capacitor between power and ground somewhere near the sensor.
A red LED on the back of the PCB lights when the output is low, indicating that the sensor is detecting something. If so desired, you can disable this LED by cutting the trace between it and the OUT pin where it is marked on the silkscreen or by desoldering the LED.
The GP2Y0D810Z0F and GP2Y0D805Z0F have an optional enable input that can be used to put the sensor into low-power mode. The Pololu carrier board connects this input to Vcc so that the sensor is always enabled, but you can solder a wire to the pad labeled “enable” on the back of the PCB if you want control over this input. Note that you will need to cut the trace that connects the enable line to Vcc on the PCB if you want to be able to disable the sensor. This trace is marked on the silkscreen, and there is a caret that indicates where we suggest you make the cut.
The carrier board has a 0.086" mounting hole for a #2 screw. You can make the module more compact by cutting or grinding off this portion of the PCB if you do not need the mounting hole.
Pololu carrier for Sharp GP2Y0D810Z0F and GP2Y0D805Z0F sensors schematic diagram. |
---|
People often buy this product together with:
Sharp GP2Y0D810Z0F Digital Distance Sensor 10cm |
Pololu Carrier with Sharp GP2Y0D810Z0F Digital Distance Sensor 10cm |
Sharp GP2Y0D805Z0F Digital Distance Sensor 5cm |
You might also like
Distance Measuring Sensor Unit Digital output (100 mm) type, voltage 2.7V-6.2V, Sharp, RoHS
Other products in the same category (16)
Module with PIR EKMC4607112K motion sensor, power consumption in standby mode up to 170 uA. The board communicates via I2C and is equipped with a Qwiic connector. SparkFun SEN-17374
Flow sensor with thread G1/4. Dedicated to liquids of high concentration and low viscosity. DFRobot SEN0549
Module with a dust sensor PPD42NS. The board is equipped with a Grove cable and communicates via the PWM interface. Seeed Studio 101020012
Module with laser distance sensor ToF VL53L0X designed for M5Stack sets. It can detect simple hand gestures. M5Stack U010
Module with 13 QTR type optocoupler with RC (digital) output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4153
Module with PM2.5 dust sensor. The board is equipped with a Gravity connector and communicates via the I2C interface. DFRobot SEN0460
Module with 11 QTR type optocoupler with analog output. The module operates from 2.9 V to 5.5 V, detects objects at a distance of up to 40 mm. The sensor will be used in projects that require detection of changes in the ground, e.g. in linefollower robots. Pololu 4211
Module with a pulse sensor and the level of SpO2 (oxygen saturation level). It is based on the MAX30102 chip, dedicated to the T-Wristband
Module with a precise temperature sensor MCP9808. It is supplied with the voltage ranging from 2.7 to 5.5 V and communicates via the I2C interface
No product available!
ToF VL53L0X distance sensor module designed for M5Stack sets. It allows you to measure distances up to 2 m and communicates via the I2C interface. M5Stack U072
ToF distance sensor module based on the VL6180X system. It offers a range of 2 to 50 cm and communicates via the I2C interface
PMS7003 is a kind of digital and universal particle concentration sensor, which can be used to obtain the number of suspended particles in the air, i.e. the concentration of particles, and output them in the form of digital interface
No product available!
Temperature and humidity module, -40C to +125C, 0 - 99.9% RH, AOSONG, RoHS
Module with a digital temperature and humidity sensor based on the SHT30. Communication via the I2C interface. DFRobot SEN0330
No product available!
KAmodQTR8A is a module with eight photointerrupter sensors KTIR0711S. It allows to detect edge or line. Thanks to the analog outputs, is possible to connect a module to the e.g. comparator. The module can be used in analisze of the floor e.g. by Linefollower vehicles.