ESP32-PICO-KIT IoT development board

Beetle ESP32 is a small (35 × 34mm) board thanks to which the creation of the Internet of Things (IoT) is very simple. The module was based on the ESP32 system, which allows for Bluetooth communication (compatible with Bluetooth 4.2) and WiFi. DFRrobot DFR0575

Development board with ESP-WROOM-32 module. It allows communication within the WiFi network and the Bluetooth 4.2 (BLE) standard

Module with WiFi Espressif ESP32-S2. It has 4MB Flash, 2MB PSRAM, and integrates a BME280 sensor, LiPo charging circuit, and RGB LED. Equipped with a STEMMA QT connector. Adafruit 5303

Module with ATSAMD51J19 microcontroller and ESP32 WiFi system dedicated to matrix displays with HUB75 interface. Adafruit 4745

Board for applications in the area of the Internet of Things (IoT). The module is based on the ESP-WROOM-32E system with 240 MHz clock, equipped with 4 MB Flash and 520 KB SRAM, as well as WiFi and Bluetooth communication. DFrobot DFR0654-F

Module with WiFi and BLE Espressif ESP32-S3. It integrates a LiPo charging circuit and an RGB diode. Adafruit 5398

The development board allows you to easily use the capabilities of ESP32 (Wi-Fi + Bluetooth BLE) from Espressif. There is a USB / UART converter on the board, and most of the GPIO line of the ESP-WROOM-32D module has been connected to pins with a pitch of 2.54mm. ESP32-DevKitC V4

Module with 9-axis IMU LSM9DS1 system dedicated to ESP Thing board. Equipped with a connector for connecting GPS and a microSD slot. SparkFun DEV-14430

ESP32-S3 development board equipped with a 32-bit dual-core Xtensa 32-bit LX7 processor. It is equipped with a 1.14-inch IPS LCD display with a resolution of 240 x 135 pixels and a micro SD card slot. It has the format of a USB dongle with a type A connector, which makes it convenient and handy to use. Waveshare ESP32-S3-GEEK

Robot controller dedicated to Totem sets. It is based on the ESP32 chip (WiFi and Bluetooth module), equipped with a DC motor and servo driver, RGB diodes and an IMU sensor. Totem TE-X4-KIT1

The SparkFun ESP32 Thing Power Control Shield enables the ESP32 Thing to switch up to 5A of a DC load, providing a wide variety of options to control your next project! With a default voltage range of 5–28VDC, power can be connected to this shield in one of two ways. DEV-14155

Powerful, generic Wi-Fi+BT+BLE MCU modules that target a wide variety of applications, ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streaming and MP3 decoding. Espressif ESP32-WROOM-32E 32MBit (4MB)

Module with WiFi Espressif ESP32-S2. It integrates two regulators, SPI Flash memory, LiPo charging circuit and RGB diode. It is equipped with a STEMMA QT connector. Adafruit 4775

Board with the WiFi Espressif ESP32-C3 module. It offers 4 MB of Flash memory and 400 KB of SRAM and an RGB diode. It is equipped with a matrix of WS2812B programmable diodes

Development board with Espressif ESP32-S3-WROOM-1 module. The module has built-in 8 MB Flash memory and 8 MB PSRAM and offers WiFi and Bluetooth LE wireless communication. Espressif Systems ESP32-S3-DevKitC-1-N8R8

Board with the WiFi Espressif ESP32-C3 module. It offers 4 MB of Flash memory and 400 KB of SRAM and an RGB diode. It is equipped with a STEMMA QT connector. Adafruit 5405