Pololu G2 High-Power Motor Driver 24v13
ID: 561024
zł173.75
Tax included
zł141.26 tax excl.
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
The Pololu G2 high-power motor driver is a discrete MOSFET H-bridge designed to drive large brushed DC motors. The H-bridge is made up of one N-channel MOSFET per leg; the rest of the board contains the circuitry to take user inputs and control the MOSFETs. The absolute maximum voltage for this motor driver is 40 V, and higher voltages can permanently destroy the motor driver. Under normal operating conditions, ripple voltage on the supply line can raise the maximum voltage to more than the average or intended voltage, so a safe maximum voltage is approximately 34 V.
NOTE: Battery voltages can be much higher than nominal voltages when they are charged, so the maximum nominal battery voltage we recommend is 28 V unless appropriate measures are taken to limit the peak voltage.
Features
- Operating voltage: 6.5 V to 40 V (absolute maximum)
- Output current: 13 A continuous
- Inputs compatible with 1.8 V, 3.3 V, and 5 V logic
- PWM operation up to 100 kHz
- Current sense output proportional to motor current (approx. 40 mV/A; only active while H-bridge is driving)
- Active current limiting (chopping) with default threshold of 30 A (can be adjusted lower)
- Reverse-voltage protection
- Undervoltage shutdown
- Short circuit protection
561024
Data sheet
- Output current
- 13 A
- Number of channels
- 1
- Supply voltage min
- 6,5 V
- Supply voltages max
- 40 V
You might also like
Pololu High-Power Motor Driver 18v15
zł258.30
Delivery date unknown
No product available!
Pololu High-Power Motor Driver 24v23 CS
zł674.05
Delivery date unknown
No product available!
Pololu High-Power Motor Driver 24v20
zł236.02
24h
Available quantity: 1
Available
Pololu High-Power Motor Driver 24v12
zł191.45
24h
Available quantity: 8
Available
Pololu High-Power Motor Driver 36v20 CS
zł498.94
24h
Available quantity: 2
Available
Other products in the same category (16)
Pololu Simple High-Power Motor Controller 24v12 (Fully Assembled)
zł646.75
24h
Available quantity: 2
Available
Dual motor controller allowing two DC motors to be driven with voltages from 4.5 to 13.5V and a continuous current of 1.2 A per channel. SparkFun ROB-14451
zł69.90
24h
Available quantity: 3
Available
Extension module with a driver for two stepper motors based on the DRV8825 system. Dedicated for Raspberry Pi minicomputers. Waveshare Stepper Motor HAT
zł111.67
4 weeks
No product available!
ESC RC controller module with FlySky receiver designed for two brush motors with a supply voltage from 2.5 to 5 V and a current consumption of 2 A
zł183.07
24h
Available quantity: 2
Available
The stepper motor driver with the MP6500 system, allows the bipolar motor to be supplied with a current of up to 2A per phase, without the use of a heat sink. The system can be supplied with voltage in the range 4.5 ... 35V. Polol 2969
zł41.59
24h
Available quantity: 2
Available
Module with a stepper motor driver based on the DRV8434A system. It allows the bipolar motor to be supplied with current up to 1.2 A per phase and with a voltage from 4.5 V to 45 V. Communication via the SPI interface. Pololu 3766
zł54.86
6 weeks
No product available!
DRV8825 Stepper Motor Driver Module for Arduino. It allows you to control two drives, equipped with an XBee connector. DFRobot DRI0023
zł180.20
24h
Available quantity: 1
Available
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5042
zł584.79
6 weeks
No product available!
Small size driver module TB67S249FTG stepper motor powered with 10 ... 47V voltage and working current of 1.6A. The controller allows you to control the motor movement up to 7 different resolutions (up to 1/32 of a step). Polol 3096
zł65.41
24h
Available quantity: 1
Available
Pololu TReX Dual Motor Controller DMC01
zł1,124.93
24h
Available quantity: 1
Available
A module with a two-channel DC motor driver based on the TB6612FNG system. Designed for Wemos D1 Mini
zł55.39
24h
Available quantity: 4
Available
RoboClaw 2x45A Motor Controller (V5D) is a two-channel DC motor driver, operating voltage: 6-34V, maximum continuous current: 45A, easy implementation of feedback loops with PID controller, safety systems. Pololu 3287
zł1,258.60
6 weeks
No product available!
A module with a fan controller and a temperature sensor based on the EMC2101 system. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4808
zł31.51
24h
Available quantity: 1
Available
Pololu Jrk 21v3 USB Motor Controller with Feedback (Fully Assembled)
zł483.56
24h
Available quantity: 1
Available
A single-channel DC motor controller with a UART TTL interface. It is powered from 4.5 V to 48 V and can deliver up to 2.2 A of current. Board with soldered connectors. Pololu 5062
zł83.92
6 weeks
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992