Products
Categories
- Main categories
-
- 3D PRINTING
- ACADEMIC OFFER
- ARDUINO
- AUTOMATION
- BOOKS
- DIY KITS
- AVT kits
- Audio
- Car
- Chargers
- Clocks, timers and schedule switches
- Communication
- Converters
- Development kits and modules
- Displays
- Electronic games
- Generators
- Hobbies and fun
- House
- Interfaces
- Light effects
- meters
- PC
- Power Supplies
- Pre-programmed circuits
- Printed circuit boards (PCB)
- Programmers
- Regulators, controllers
- Remote control
- Starter sets Ośla Łączka
- Starting sets for beginners
- Workshop tools
- Audio
- Other sets
- TOP-Q kits
- Totem
- UGears
- Velleman
- AVT kits
- EBOOKS
- ELECTRONICS
- Cables
- Cameras and accessories
- Communication
- Conductive materials
- Connectors
- ARK connectors (Terminal Block)
- Coaxial connectors (RF)
- Connectors
- Crocodile clip
- D-Sub drawer connectors
- DC power connectors
- FFC/FPC ZIF connectors
- Goldpin connectors
- IDC connectors
- JACK connectors
- JST connectors
- Jumpers
- Memory cards slots
- Other connectors
- Pogo pin
- RJ45 sockets
- Slip ring connector
- Supports
- Szybkozłącza
- USB connectors
- Cooling
- Displays
- Electronic modules
- A/D and D/A converters
- Audio
- Barcode readers
- CAN converters
- Converters USB - UART / RS232
- Data logger
- DDS/PLL generators
- Digital potentiometers
- Encoders
- Expanders of the I/O
- Fingerprint readers
- HMI modules
- Image and video
- JTAG accessories
- Keyboards, buttons
- LED drivers
- Memory card readers
- Memory modules
- Modules with power outputs
- Motor controllers
- Power modules
- RS485 converters
- RTC modules
- Servo Controllers
- TSOP infrared receivers
- USB Converters - I2C / 1-Wire / SPI
- Voltage converters
- Gadgets
- GPS
- Intelligent clothes
- LED - diodes, displays, stripes
- Luminous wires and accessories
- Memory cards and other data storages
- Passive elements
- PC accessories
- Printers
- Prototype boards
- Semiconductors
- A/C converters (ADC)
- Analog systems
- Audio systems
- Bridge rectifiers
- Button
- D/A Converters (DAC)
- DDS synthesizers
- Digital circuits
- Diodes
- Drivers of motors
- DSP microprocessors
- Energy counters
- Energy harvesting
- ESD security
- IGBT drivers and bridges
- Interface systems
- LED drivers
- Logic converters
- Memory
- Microcontrollers
- Optotriacs and optocouplers
- Other
- PLL generators
- Power systems
- Programmable systems
- Resetting systems
- RF systems
- RTC systems
- Sensors
- SoC systems
- Timery
- Touch sensors
- Transistors
- Sensors
- Accelerometers
- Air humidity sensors
- Air quality sensors
- Current sensors
- Distance sensors
- Flow sensors
- Gas sensors
- Gyroscopes
- Hall sensors
- Humidity sensors
- Infrared sensors
- Light and color sensors
- Liquid level sensors
- Magnetic sensors (compasses)
- Medical sensors
- Motion sensors
- PH sensors
- Position sensors
- Pressure sensors
- Pressure sensors
- Reflection sensors
- Sensors 6DOF/9DOF/10DOF
- Sensors of liquid quality
- Temperature sensors
- Vibration sensors
- Sound transducers
- Switches and buttons
- Cables
- INTERNET OF THINGS (IoT)
- MECHANICS
- POWER
- R/C MODELLING
- RASPBERRY PI
- Accessories for Raspberry Pi
- Audio video cables for Raspberry Pi
- Case Raspberry Pi
- Cooling for Raspberry Pi
- Displays for Raspberry Pi
- Extension modules for Raspberry Pi
- Memory cards for Raspberry Pi
- Power for Raspberry Pi
- Raspberry Pi 3 model A+
- Raspberry Pi 3 model B
- Raspberry Pi 3 model B+
- Raspberry Pi 4 model B
- Raspberry Pi 400
- Raspberry Pi 5
- Raspberry Pi cameras
- Raspberry Pi Compute Module
- Raspberry Pi model A/ B+/2
- Raspberry Pi Pico
- Raspberry Pi prototyping
- Raspberry Pi Zero
- Raspberry Pi Zero 2 W
- RETIRED PRODUCTS
- ROBOTICS
- SALE
- SOFTWARE
- STARTER KITS, PROGRAMMERS, MODULES
- Alchitry FPGA
- Altera FPGA
- Analog electronics
- Atmel SAM
- Atmel Xplain
- AVR
- Banana Pi
- BeagleBone
- chipKIT
- Coral
- CPLD Xilinx
- Cubieboard
- DFRobot FireBeetle
- Feather
- Freedom (Kinetis)
- FriendlyELEC
- HummingBoard
- Intelligent clothes
- Kit with a book
- LattePanda
- LPC (NXP)
- M5Stack
- Micro:bit
- Nvidia Jetson
- Odroid
- ODYSSEY
- Orange Pi
- Other development kits
- Peripheral modules
- PIC
- Raisonance
- Raspberry Pi RP2040
- RFID
- RISC-V
- SBC Embest
- SBC MYIR
- SBC others
- SBC UDOO
- Segger programmers
- SoMLabs
- Sparkfun MicroMod
- STM32
- STM32 Discovery
- STM32 MP1
- STM32 Nucleo boards
- STM8
- Teensy
- Universal programmers
- WRTNode
- Xilinx FPGAs
- WORKSHOP
- Adhesives and gluers
- Anti-static mats (ESD)
- Chemistry
- CNC milling machines
- Crimping tools
- Dispensing needles
- Drills
- Files
- Generators
- Handles, magnifiers
- Heat-shrink tubing
- Insulation strippers
- Keys
- Knives and scissors
- Laboratory power supplies
- Laminates
- Measuring devices
- Mikroskopy
- Mini drills and grindrers
- Organizers
- Oscilloscopes and accessories
- Pliers and pincers
- Riveting tools and rivets
- Screwdrivers
- SMD Accessories
- Soldering
- Tapes (aluminum, kapton, copper, insulating)
- Tweezers
- Ultrasonic cleaners
- Vices
- 3D PRINTING
New products
New products
zł35.55 tax excl.
Pololu 2831
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Pololu 5V, 1A Step-Down Voltage Regulator D24V10F5
The compact (0.5″ × 0.7″) D24V10F5 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 5 V while allowing for a maximum output current of 1 A. This regulator offers typical efficiencies between 85% and 90% and has a very low dropout, so it can be used with input voltages as low as a few hundred millivolts above 5 V. The pins have a 0.1″ spacing, making this board compatible with standard solderless breadboards and perfboards.
Description
The D24V10Fx family of step-down voltage regulators features the Intersil ISL85410 1A synchronous buck regulator and generates lower output voltages from input voltages as high as 36 V. They are switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters) with typical efficiencies between 80% and 93%, which is much more efficient than linear voltage regulators, especially when the difference between the input and output voltage is large. These regulators have a power-save mode that activates at light loads and a low quiescent (no load) current draw, which make them well suited for applications that are run from a battery.
The different versions of this regulator all look very similar, so the bottom silkscreen includes a blank space where you can add your own distinguishing marks or labels. This product page applies to all five versions of the D24V10Fx family.
The SHDN pin can be used to put the board in a low-power state that reduces the quiescent current to approximately 10 µA to 20 µA per volt on VIN, and a PG (power good) output can be used to monitor the state of the regulator’s output voltage.
The regulators feature short-circuit/over-current protection, and thermal shutdown helps prevent damage from overheating. The boards do not have reverse-voltage protection.
Features
- Input voltage: [output voltage + dropout voltage] to 36 V (see below for more information on dropout voltage)
- Fixed 3.3 V, 5 V, 6 V, 9 V, or 12 V output (depending on regulator version) with 4% accuracy
- Maximum output current: 1 A
- Typical efficiency of 80% to 93%
- 500 kHz switching frequency (when not in power-save mode)
- 2 ms soft-start reduces in-rush current on power-up
- 200 μA typical no-load quiescent current
- Integrated over-temperature and over-current shutoff
- Small size: 0.7″ × 0.5″ × 0.14″ (18 mm × 13 mm × 3.5 mm)
Connections
The buck regulator has five connections: power good (PG). shutdown (SHDN), input voltage (VIN), ground (GND), and output voltage (VOUT).
The “power good” indicator, PG, is an open-drain output that drives low when the regulator’s output voltage falls below 80% or rises above 120% of its target output voltage. This output is also actively held low for the duration of the regulator’s 2 ms soft-start period and while the regulator is being disabled by the SHDN input or by over-temperature or over-current fault conditions. An external pull-up resistor is generally required to use this pin.
The SHDN pin can be driven low (under 0.4 V) to turn off the output and put the board into a low-power state. There is a 100 kΩ pull-up resistor between the SHDN pin and VIN, so if you want to leave the board permanently enabled, the SHDN pin can be left disconnected. While the SHDN pin is being driven low, the current draw of the regulator is dominated by the current through the pull-up resistor and will be proportional to the input voltage. (At 36 V in it will draw about 360 μA.)
The input voltage, VIN, powers the regulator. Voltages between 3 V and 36 V can be applied to VIN, but the effective lower limit of VIN is VOUT plus the regulator’s dropout voltage, which varies approximately linearly with the load (see below for graphs of dropout voltages as a function of the load). Additionally, please be wary of destructive LC spikes (see below for more information).
The output voltage, VOUT, is fixed and depends on the regulator version: the D24V10F3 version outputs 3.3 V, the D24V10F5 version outputs 5 V, the D24V10F6 version outputs 6 V, the D24V10F9 version outputs 9 V, and the D24V10F12 version outputs 12 V.
Typical efficiency and output current
The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. This family of switching regulators typically has an efficiency of 80% to 93%, though the actual efficiency in a given system depends on input voltage, output voltage, and output current. See the efficiency graph near the bottom of this page for more information.
In order to achieve a high efficiency at low loads, this regulator automatically goes into a power-save mode where the switching frequency is reduced. In power-save mode, the switching frequency of the regulator changes as necessary to minimize power loss. This could make it harder to filter out noise on the output caused by switching.
Typical dropout voltage
The dropout voltage of a step-down regulator is the minimum amount by which the input voltage must exceed the regulator’s target output voltage in order to ensure the target output can be achieved. For example, if a 5 V regulator has a 1 V dropout voltage, the input must be at least 6 V to ensure the output is the full 5 V. Generally speaking, the dropout voltage increases as the output current increases. See the “Details” section below for more information on the dropout voltage for this specific regulator version.
Details for item #2831
The graphs below show the typical efficiency and dropout voltage of the 5 V D24V10F5 regulator as a function of the output current:
LC voltage spikes
When connecting voltage to electronic circuits, the initial rush of current can cause voltage spikes that are much higher than the input voltage. If these spikes exceed the regulator’s maximum voltage (36 V), the regulator can be destroyed. In our tests with typical power leads (~30″ test clips), input voltages above 20 V caused spikes over 36 V.
Specifications
- Minimum operating voltage: 5.1 V2
- Maximum operating voltage: 36 V
- Maximum output current: 1 A
- Output voltage: 5 V
- Reverse voltage protection?: N
- Maximum quiescent current: 0.2 mA
Download
Other products in the same category (16)
Step-Down DC-DC converter module based on the D36V6F12 system. Input voltage 12.2.50V, output voltage 12V (max. 600mA). Pololu 3796
DC-DC Step-Up converter U3V40F7 with an output voltage of 7.5 V, an input voltage of 1.3 to 7.5 V and a maximum output current of 4 A. Pololu 4014
Step-Down converter with an output voltage of 5 V, an input voltage of 6.5 to 16 V and a maximum current of 4 A
Step-Down converter D36V28F5 with an output voltage of 5 V, an input voltage from 5.3 to 50 V and a maximum output current of 4 A. Pololu 3782
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 38 V and efficiently reduces it to 5 V. The board measures only 0.7″ × 0.8″, but it allows a typical continuous output current of up to 5 A. Typical efficiencies of 85% to 95% make this regulator well suited for high-power applications like powering motors or servos.
Step Down converter module with an output voltage from 5 to 12 V and a maximum load of 3.4 A. The board is equipped with two USB connectors and has a built-in fast charging function for smartphones
This small synchronous switching step-down (or buck) regulator takes an input voltage of up to 36 V and efficiently reduces it to 7.5 V. The board measures only 0.7″ × 0.7″ yet delivers a typical continuous output current of up to 2.4 A and features reverse voltage protection.
No product available!
The compact (0.4″ × 0.5″) D24V5F6 synchronous buck voltage regulator takes an input voltage of up to 36 V and efficiently reduces it to 6 V while allowing for a maximum output current of 500 mA. Pololu 2844
No product available!
Step-Down converter D36V50F3 with an output voltage of 3.3 V, an input voltage from 4.5 to 50 V and a maximum output current of 9.5 A. Pololu 4090
Step-Down converter with an output voltage of 5 V, an input voltage of 7 to 26 V and a maximum current of 3 A
This compact (0.4″ × 0.5″) switching step-down (or buck) voltage regulator takes input voltages between 4 V and 50 V and efficiently reduces them to a lower, user-adjustable voltage set by an on-board trimmer potentiometer. It has an output voltage range of 2.5 V to 7.5 V and a maximum output current of 600 mA.
No product available!
DC-DC Step-Down Converter ME3116AM6G with an output voltage of 5 V, input voltage from 6 to 24 V and a maximum output current of 1 A. Dedicated to the M5Stack modules. M5Stack U125
Step-Down converter with an output voltage of 5 V, input voltage from 9 to 36 V and a maximum current of 5 A. The board is equipped with a DC input connector and an output USB connector
The Step-Down D24V6F5 Buck Voltage Regulator module gives the output voltage of 5V with a wide input voltage range of 7-42V and a maximum output current of 600 mA. Pololu 2107
No product available!
Step-Down converter D36V50F12 with an output voltage of 12 V, an input voltage from 13.3 to 50 V and a maximum output current of 6.5 A. Pololu 4095