- Out-of-Stock
Products
Categories
- Main categories
-
- 3D PRINTING
- ACADEMIC OFFER
- ARDUINO
- AUTOMATION
- BOOKS
- DIY KITS
- AVT kits
- Audio
- Car
- Chargers
- Clocks, timers and schedule switches
- Communication
- Converters
- Development kits and modules
- Displays
- Electronic games
- Generators
- Hobbies and fun
- House
- Interfaces
- Light effects
- meters
- PC
- Power Supplies
- Pre-programmed circuits
- Printed circuit boards (PCB)
- Programmers
- Regulators, controllers
- Remote control
- Starter sets Ośla Łączka
- Starting sets for beginners
- Workshop tools
- Audio
- Other sets
- TOP-Q kits
- Totem
- UGears
- Velleman
- AVT kits
- EBOOKS
- ELECTRONICS
- Cables
- Cameras and accessories
- Communication
- Conductive materials
- Connectors
- ARK connectors (Terminal Block)
- Coaxial connectors (RF)
- Connectors
- Crocodile clip
- D-Sub drawer connectors
- DC power connectors
- FFC/FPC ZIF connectors
- Goldpin connectors
- IDC connectors
- JACK connectors
- JST connectors
- Jumpers
- Memory cards slots
- Other connectors
- Pogo pin
- RJ45 sockets
- Slip ring connector
- Supports
- Szybkozłącza
- USB connectors
- Cooling
- Displays
- Electronic modules
- A/D and D/A converters
- Audio
- Barcode readers
- CAN converters
- Converters USB - UART / RS232
- Data logger
- DDS/PLL generators
- Digital potentiometers
- Encoders
- Expanders of the I/O
- Fingerprint readers
- HMI modules
- Image and video
- JTAG accessories
- Keyboards, buttons
- LED drivers
- Memory card readers
- Memory modules
- Modules with power outputs
- Motor controllers
- Power modules
- RS485 converters
- RTC modules
- Servo Controllers
- TSOP infrared receivers
- USB Converters - I2C / 1-Wire / SPI
- Voltage converters
- Gadgets
- GPS
- Intelligent clothes
- LED - diodes, displays, stripes
- Luminous wires and accessories
- Memory cards and other data storages
- Passive elements
- PC accessories
- Printers
- Prototype boards
- Semiconductors
- A/C converters (ADC)
- Analog systems
- Audio systems
- Bridge rectifiers
- Button
- D/A Converters (DAC)
- DDS synthesizers
- Digital circuits
- Diodes
- Drivers of motors
- DSP microprocessors
- Energy counters
- Energy harvesting
- ESD security
- IGBT drivers and bridges
- Interface systems
- LED drivers
- Logic converters
- Memory
- Microcontrollers
- Optotriacs and optocouplers
- Other
- PLL generators
- Power systems
- Programmable systems
- Resetting systems
- RF systems
- RTC systems
- Sensors
- SoC systems
- Timery
- Touch sensors
- Transistors
- Sensors
- Accelerometers
- Air humidity sensors
- Air quality sensors
- Current sensors
- Distance sensors
- Flow sensors
- Gas sensors
- Gyroscopes
- Hall sensors
- Humidity sensors
- Infrared sensors
- Light and color sensors
- Liquid level sensors
- Magnetic sensors (compasses)
- Medical sensors
- Motion sensors
- PH sensors
- Position sensors
- Pressure sensors
- Pressure sensors
- Reflection sensors
- Sensors 6DOF/9DOF/10DOF
- Sensors of liquid quality
- Temperature sensors
- Vibration sensors
- Sound transducers
- Switches and buttons
- Cables
- INTERNET OF THINGS (IoT)
- MECHANICS
- POWER
- R/C MODELLING
- RASPBERRY PI
- Accessories for Raspberry Pi
- Audio video cables for Raspberry Pi
- Case Raspberry Pi
- Cooling for Raspberry Pi
- Displays for Raspberry Pi
- Extension modules for Raspberry Pi
- Memory cards for Raspberry Pi
- Power for Raspberry Pi
- Raspberry Pi 3 model A+
- Raspberry Pi 3 model B
- Raspberry Pi 3 model B+
- Raspberry Pi 4 model B
- Raspberry Pi 400
- Raspberry Pi 5
- Raspberry Pi cameras
- Raspberry Pi Compute Module
- Raspberry Pi model A/ B+/2
- Raspberry Pi Pico
- Raspberry Pi prototyping
- Raspberry Pi Zero
- Raspberry Pi Zero 2 W
- RETIRED PRODUCTS
- ROBOTICS
- SALE
- SOFTWARE
- STARTER KITS, PROGRAMMERS, MODULES
- Alchitry FPGA
- Altera FPGA
- Analog electronics
- Atmel SAM
- Atmel Xplain
- AVR
- Banana Pi
- BeagleBone
- chipKIT
- Coral
- CPLD Xilinx
- Cubieboard
- DFRobot FireBeetle
- Feather
- Freedom (Kinetis)
- FriendlyELEC
- HummingBoard
- Intelligent clothes
- Kit with a book
- LattePanda
- LPC (NXP)
- M5Stack
- Micro:bit
- Nvidia Jetson
- Odroid
- ODYSSEY
- Orange Pi
- Other development kits
- Peripheral modules
- PIC
- Raisonance
- Raspberry Pi RP2040
- RFID
- RISC-V
- SBC Embest
- SBC MYIR
- SBC others
- SBC UDOO
- Segger programmers
- SoMLabs
- Sparkfun MicroMod
- STM32
- STM32 Discovery
- STM32 MP1
- STM32 Nucleo boards
- STM8
- Teensy
- Universal programmers
- WRTNode
- Xilinx FPGAs
- WORKSHOP
- Adhesives and gluers
- Anti-static mats (ESD)
- Chemistry
- CNC milling machines
- Crimping tools
- Dispensing needles
- Drills
- Files
- Generators
- Handles, magnifiers
- Heat-shrink tubing
- Insulation strippers
- Keys
- Knives and scissors
- Laboratory power supplies
- Laminates
- Measuring devices
- Mikroskopy
- Mini drills and grindrers
- Organizers
- Oscilloscopes and accessories
- Pliers and pincers
- Power tools
- Riveting tools and rivets
- Screwdrivers
- SMD Accessories
- Soldering
- Tapes (aluminum, kapton, copper, insulating)
- Tweezers
- Ultrasonic cleaners
- Vices
- 3D PRINTING
New products
New products
Pololu 12V Step-Up Voltage Regulator U3V12F12
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Pololu 12V Step-Up Voltage Regulator U3V12F12
The compact (0.32"×0.515") U3V12F12 switching step-up (or boost) voltage regulator takes an input voltage as low as 2.5 V and efficiently boosts it to 12 V. The pins have a 0.1" spacing, making this board compatible with standard solderless breadboards and perfboards.
Overview
These boost (step-up) voltage regulators generate higher output voltages from input voltages as low as 2.5 V. They are switching regulators (also called switched-mode power supplies (SMPS) or DC-to-DC converters) and have a typical efficiency between 80% to 90%. The available output current is a function of the input voltage, output voltage, and efficiency (see Typical Efficiency and Output Current section below), but the input current can typically be as high as 1.4 A. This regulator is available with a fixed 5 V, 9 V, or 12 V output:
The regulator’s thermal shutdown prevents damage from overheating, but it does not have short-circuit or reverse-voltage protection.
Features
- input voltage: 2.5 V – VOUT
- fixed 5 V, 9 V, or 12 V output with 4% accuracy
- 1.4 A switch allows for input currents up to 1.4 A
- 2 mA typical no-load quiescent current
- integrated over-temperature shutoff
- small size: 0.515" × 0.32" × 0.1" (13 × 8 × 3 mm)
Using the Regulator
Connections
The boost regulator has three connections: input voltage (VIN), ground (GND), and output voltage (VOUT).
The input voltage, VIN, must be at least 2.5 V and should not exceed the output voltage, VOUT. Please be wary of destructive LC spikes that might cause the input voltage to exceed VOUT (see below for more information).
The three connections are labeled on the back side of the PCB, and they are arranged with a 0.1" spacing along the edge of the board for compatibility with solderless breadboards, connectors, and other prototyping arrangements that use a 0.1" grid. You can solder wires directly to the board or solder in either the 3×1 straight male header strip or the 3×1 right-angle male header strip that is included.
Typical Efficiency and Output Current
The efficiency of a voltage regulator, defined as (Power out)/(Power in), is an important measure of its performance, especially when battery life or heat are concerns. As shown in the graphs below, this switching regulator typically has an efficiency of 80 to 90%.
The maximum achievable output current is approximately proportional to the ratio of the input voltage to the output voltage. If the input current exceeds the switch current limit (typically somewhere between 1.4 and 2 A), the output voltage will begin to drop. Additionally, the maximum output current can depend on other factors, including the ambient temperature, air flow, and heat sinking.
LC Voltage Spikes
When connecting voltage to electronic circuits, the initial rush of current can cause damaging voltage spikes that are much higher than the input voltage. In our tests with typical power leads (~30" test clips), input voltages above 10 V caused voltage spikes in excess of 20 V. You can suppress such spikes by soldering a 33µF or larger electrolytic capacitor close to the regulator between VIN and GND.
More information about LC spikes can be found in our application note, Understanding Destructive LC Voltage Spikes.
People often buy this product together with:
Pololu 5V Step-Up Voltage Regulator U3V12F5 |
Pololu Adjustable Boost Regulator 4-25V |
Pololu 9V Step-Up Voltage Regulator U3V12F9 |
You might also like
Step-up DC-DC converter module, 0.9-5V input voltage, 5V output voltage (max. 500 mA) connected to the USB socket. There is a diode on the board indicating the power connection
No product available!
DC-DC Step-up converter module based on the U3V70F12 system. Input voltage 2.9-12V, output voltage 12V, maximum current 10A. Two mounting holes. Pololu 2895
Other products in the same category (16)
No product available!
No product available!
ROSA3D filament made of high-quality PLA granules. 0.8 kg of filament with a diameter of 1.75 mm is wound on the spool. ROSA3D PLA Starter Gray
No product available!
No product available!
No product available!
Permanent cylindrical neodymium magnet with a diameter of 4 mm and a height of 1,5 mm.
No product available!
Hardware extension adds Narrow Band 169 MHz radio communication capability to Open4, EvoPrimer and STM32 Primer2 platforms
No product available!
No product available!
No product available!
This high discharge LiPo - a great way to power any R/C, robotic, or portable project; excellent choice for anything that requires a small battery with a lot of punch. This battery has two cells and outputs 7.4V storing 2200mAh of charge. PRT-11856
No product available!
Board with a 32-bit Nuvoton NUC123ZD4AN0 microcontroller with an ARM Cortex-M0 core, the user has 31 I / O lines, 6 analog inputs and UART, SPI, I2S and I2C interfaces. Compatible with Arduino. DFRobot DFR0392
No product available!
The module allows measuring the magnetic field in three XYZ planes, equipped with an HMC5883L sensor with an I2C interface. MOD-63
No product available!
LCD 2x16, 80x36mm, LED backlight (yellow-green), FSTN NEGATIVE, second character set - cyryllic (v.E50-MIY), enhanced temperature range, "fast"
No product available!
No product available!
No product available!
The housing for Orange Pi Plus is transparent, with snaps. The installation does not require the use of glue. The housing is made of high quality plastic. All openings made in the housing allow easy access to every socket built in Orange Pi Plus
No product available!