Zamów i zapłać w ciągu
a przesyłkę wyślemy jeszcze dzisiaj
Zestaw ewaluacyjny z układem Zynq Ultrascale+ MPSoC, integrujący ARM...
Zasilacz o mocy 120W, napięciu wyjściowym 24VDC oraz prądzie...
Karta pamięci przeznaczona dla sterowników...
W zestawie promocyjnym:Raspberry Pi 4 model B z 2GB RAMNajnowsza...
Zestaw startowy z modułem logicznym LOGO! 8 12/24RCE, panelem HMI,...
Panel operatorski HMI z dotykowym wyświetlaczem TFT o przekątnej 7" o...
Taśma FFC/FPC 50 żył o długości 20 cm i rastrze 0,5mm, typ A-A
Wysokiej jakości oraz czystości średnio aktywny topnik ułatwiający...
Terenowe podwozie Dagu Wild Thumper 6WD w kolorze czarnym, w komplecie koła o średnicy 120mm oraz silniki z przekładnią 75:1. Podwozie jest wykonane z blachy aluminiowej, otwory o średnicy 4mm rozmieszczone co 10mm umożliwiają montaż kontrolera oraz akcesoriów. Pololu 1563
Dagu Wild Thumper 6WD All-Terrain Chassis, Black, 75:1
This rugged, 6-wheel-drive chassis from Dagu Electronics has independent suspension for each of its spiked 120mm-diameter wheels, allowing exceptional traction over uneven terrain, and its body is made from 2mm-thick anodized aluminum with a 10mm-pitch grid of 4mm holes, making it easy to mount electronics and accessories to the chassis. Assembly of the chassis is a simple three-step process that takes just minutes. This model is black with 75:1 steel gearboxes on the motors. It might have metallic-red hubs (as shown in the main product picture) or gold hubs (not pictured).
|Bottom view of Dagu Wild Thumper 6WD chassis (silver version).|
This rugged, 6-wheel-drive chassis from Dagu Electronics is designed to excel at traversing rough terrain and steep inclines, making it a great platform for any robot that needs to perform tasks in a complex outdoor environment. It features six powerful DC motors with brass brushes and 34:1 or 75:1 steel gearboxes that drive large (120mm diameter) spiked tires, and a unique “super-twist” suspension system acts to keep each wheel in contact with the ground for maximum traction, even when driving over uneven or bumpy surfaces. The suspension can be adjusted to suit different loads and conditions. The chassis is made from a 2mm-thick corrosion-resistant anodized aluminum plate, all of the nuts, bolts, and screws are stainless steel, and the brass fittings and suspension springs are nickel-plated.
When powered at 7.2 V, the version of the chassis with 34:1 gearboxes can reach a top speed of approximately 7 km/h (4.5 mph), and each motor has a stall torque of roughly 5 kg-cm (70 oz-in). At the same voltage, the version of the chassis with 75:1 gearboxes can reach a top speed of approximately 3 km/h (2 mph), and each motor has a stall torque of roughly 11 kg-cm (150 oz-in).
The chassis’ aluminum plate has 4mm holes spaced every 10mm, providing plenty of options when it comes to mounting your control electronics, sensors, and additional hardware, and with a maximum recommended payload of 5 kg (11 lb), this platform is capable of carrying a lot of cargo! Two compartments in the chassis have been designed to hold 7.2V sub-C battery packs (not included) that are commonly used in RC cars. A total of four such battery packs can fit in these compartments. The interior of the chassis also features convenient screw terminals for connecting your battery and motor driver leads. The motor leads are pre-connected to these screw terminals.
|Side view of Dagu Wild Thumper 6WD chassis (black version).|
|Dagu Wild Thumper wheel 120×60mm (chrome) with Pololu 25D mm metal gearmotor.|
This is a differential-drive chassis, meaning that turning is accomplished by driving the motors on the two sides of the platform at different speeds. The three motors on each side of the robot are wired in parallel, so only two channels of motor control are required to get this chassis moving. The motors are intended for a maximum nominal operating voltage of 7.2 V (2V minimum), and each has a stall current of 6.6 A and a no-load current of 420 mA at 7.2 V. Since the motors will briefly draw the full stall current when abruptly starting from rest (and nearly twice the stall current when abruptly going from full speed in one direction to full speed in the other), we recommend a motor driver capable of supplying the 20A combined per-channel stall current of these motors at 7.2 V. We offer several motor controllers that meet these power requirements and make it easy to get this chassis moving:
|Dagu Wild Thumper 6WD all-terrain chassis, silver.|
|Dagu Wild Thumper 6WD all-terrain chassis, black with chrome-colored hubs.|
This chassis is available in two different colors (silver and black) and with two different gear ratios (34:1 and 75:1):
|Dagu Wild Thumper 4WD all-terrain chassis, black.|
If you are looking for a smaller, less expensive chassis, consider one of the Wild Thumper 4WD models:
If you are looking for a bigger robot that is better at scaling inclines, consider one of the Wild Thumper 6WD models:
The higher gear ratio version has a lower top speed but can produce greater torque. Note that while the Wild Thumper chassis includes six wheels, the wheels can be purchased in pairs for use as replacement Wild Thumper parts or as wheels for custom chassis. The wheels are available with metallic-orange/gold hubs and chrome-colored hubs. We also offer the Wild Thumper gearmotors individually in a wide range of gear ratios (versions with integrated quadrature encoders are also available, though these will not work with the Wild Thumper chassis).
34:1 gear ratio version with black chassis and metallic-red hubs driving around a construction site:
34:1 gear ratio version with black chassis and metallic-red hubs driving up and down a set of stairs:
75:1 gear ratio version with silver chassis and chrome-colored hubs driving on snow:
|Pololu TReX Dual Motor Controller DMC01|