List of products by brand Cytron

Single-channel DC motor controller that allows the motor to be controlled with a voltage range of 6-30V and a current of up to 13A. Allows engine speed control using PWM signals. Cytron MD13S

Board compatible with Arduino Nano. It is based on the ATmega328P microcontroller with 32 KB Flash, 2 KB SRAM and 1 KB EEPROM. It has 12 LEDs, a buzzer and a user button. Cytron Maker Nano

Single-channel DC motor controller that allows the motor to be controlled with a voltage range of 6-30V and a current of up to 20A. Allows engine speed control using PWM signals. MD20A cytron

Single-channel DC motor controller enabling motor control with voltage in the range of 7-30V and current up to 10A. The set has a potentiometer and a direction switch. Cytron MD10_POT

A set of stickers with a description of the pins dedicated to the Maker UNO plates. Cytron MAKER-UNO-STICKER

Development board with RP2040 microcontroller. Equipped with a driver for DC motors, servos and Grove connectors. Dedicated to the construction of robots. Cytron MAKER-PI-RP2040

Two-channel driver of direct current (DC) motors with an operating voltage from 4 to 16 V and a maximum continuous current of 3 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD3A

Capacitive soil moisture sensor with analog output (Grove connector). The probe has a pointed tip, which allows it to be easily inserted into the ground. Cytron MAKER-SOIL-MOISTURE

The board is compatible with Arduino, based on the ATmega328P microcontroller from the AVR family, 14 I/O lines, 6 PWM channels, 6 analog inputs are available to the user. The CH340G chip communicates via a USB interface. In addition, it has 12 LEDs, a programmable button and a embedded buzzer. Cytron Uno Maker

Two-channel driver of direct current (DC) motors with an operating voltage from 5 to 30 V and a maximum continuous current of 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD10A

Development board equipped with RP2040 microcontroller, RGB LED diodes, buzzer and Qwiic/STEMMA QT connectors. Pin spacing compatible with Arduino Nano. Cytron MAKER-NANO-RP2040

Module with an analog IR reflective sensor. It consists of an IR diode and a phototransistor which measures the intensity of the reflected light. Used, among others in line tracking robots. Cytron MAKER-REFLECT

DC motor driver with a working voltage from 5 to 30 V and a maximum continuous current of 13 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MD10C

Base board designed for Raspberry Pi Pico. Equipped with numerous connectors, audio output, buzzer, micro SD slot, buttons and LEDs. Cytron MAKER-PI-PICO-NB

Dual DC motor controller with voltage from 2.5 to 9.5V with 1A continuous current per channel. Has an embedded voltage regulator. Cytron Maker Drive

Base board with soldered Raspberry Pi Pico module. Equipped with numerous connectors, buzzer, buttons and LEDs. Cytron MAKER-PI-PICO-MINI

A base board dedicated to Raspberry Pi CM4 modules. It is equipped with connectors for all available interfaces, in addition there is an RTC chip on the board Grove ports dedicated to the connection of external expansion modules. Cytron CM4 Maker Board

Base board designed for Raspberry Pi Pico. Equipped with numerous connectors, buzzer, buttons and LEDs. Cytron MAKER-PI-PICO-MINI-NB

Two-channel DC motor driver with an operating voltage from 7 to 35 V and a maximum continuous current of 30 A. It can be controlled by an analog signal, PWM, UART, RC signal or by means of built-in buttons. Cytron MDDS30

Module with an analog current sensor. It enables the measurement of alternating and direct currents up to 50 A. Cytron BB-ACS756