Cytron MD20A is a motor controller that allows you to control the speed and direction of the DC motor with a voltage in the range of 6-30 V. Based on MOSFET transistors so it can control current up to 20 A without additional cooling. The module can be controlled via PWM and DIR inputs. Thanks to the input logic voltage range from 1.8 V to 12 V, it is compatible with a wide range of controllers.
Embedded test buttons and engine output LEDs allow functional testing of the motor controller in a quick and convenient way without connecting the controller.
Attention!
Power input does not have reverse-voltage protection. Connecting the battery in reverse polarity will damage the motor driver instantaneously.Exmaple connection
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
The board is compatible with Arduino, based on the ATmega328P microcontroller from the AVR family, 14 I/O lines, 6 PWM channels, 6 analog inputs are available to the user. The CH340G chip communicates via a USB interface. In addition, it has 12 LEDs, a programmable button and a embedded buzzer. Cytron Uno Maker
Overlay compatible with Raspberry Pi Zero, Zero W, Zero WH, 1A+, 3A+, 3B, 3B+, 4B. Includes LEDs, buttons, USB-UART converter (USB connector) and buzzer. Cytron Maker pHAT
Dual DC motor controller with voltage from 2.5 to 9.5V with 1A continuous current per channel. Has an embedded voltage regulator. Cytron Maker Drive
No product available!
Module with five reflection sensors. It has digital and analogue outputs. Thanks to the embedded EEPROM memory, it enables easy sensor calibration. Cytron Maker Line
Single-channel DC motor controller enabling motor control with voltage in the range of 7-30V and current up to 10A. The set has a potentiometer and a direction switch. Cytron MD10_POT
This shield makes it easy to control two high-power DC motors with your Arduino or Arduino-compatible board. Its twin discrete MOSFET H-bridges support a wide 6.5 V to 30 V operating range and are efficient enough to deliver a continuous 18 A without a heat sink.
Pololu Simple High-Power Motor Controller 18v15
No product available!
Dual VNH2SP30 Motor Driver Carrier MD03A
Pololu High-Power Motor Driver 24v20
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5075
Dual MC33926 Motor Driver CarrierTwo-channel DC motor controller with voltage from 5 V to 28 V, power consumption up to 3 A per channel. Controlled by PWM signal. Pololu 1213
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5053
No product available!
Module with DC motor driver DRV8874. It can work with motors supplied with the voltage from 4.5 to 37 V and current consumption up to 2.1 A. Pololu 4035
Pololu High-Power Motor Driver 24v12
An H-bridge capable of controlling one DC motor in both directions or two unidirectional motors at voltages from 4.5 to 44 V and continuous current up to 1.1 A. The module offers three operating modes (PH/EN, IN/IN, half-bridge), built-in current limiting and measurement, and protection against overheating, overload, undervoltage, and reverse polarity. Its compact design, flexible logic power supply (1.8–5.5 V), and simple control make it ideal for robotics, automation, and hobby projects. Pololu 4972
The DC motor driver module enables the motor to be controlled using a PWM signal with several supply voltages (3V, 6V, 12V, 24V and 35V) and a maximum continuous current of 5A.
A two-channel DC motor controller with an I2C interface. It is powered from 4.5 V to 48 V and can deliver up to 1.8 A per motor. A board with connectors for mounting. Pololu 5065
No product available!
Module with 2-channel driver for DC motors L298P. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 105020093
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5044
No product available!
Pololu Simple Motor Controller 18v7 (Fully Assembled)
Pololu High-Power Motor Driver 36v9
Single-channel DC motor controller that allows the motor to be controlled with a voltage range of 6-30V and a current of up to 20A. Allows engine speed control using PWM signals. MD20A cytron