Dual TB6612FNG - dual DC motor driver (with connectors)
ID: 1183405
5906623418510
zł81.77
Tax included
zł66.48 tax excl.
Dual motor controller allowing two DC motors to be driven with voltages from 4.5 to 13.5V and a continuous current of 1.2 A per channel. SparkFun ROB-14450
Description
Compact dual DC motor controller. It allows two DC motors to be controlled with voltages ranging from 4.5 to 13.5 V. The controller is based on Toshiba's TB6612FNG chip, which allows a current of 1.2 A (3.2 A peak) to be drawn from each channel. Two input signals (IN1 and IN2) are used for control and can be used to control the motor in one of four functional modes: CW, CCW, short brake and stop. The two motor outputs (A and B) can be controlled separately and the speed of each motor is controlled by a PWM input signal of up to 100 kHz. To bring the motor out of standby mode, the STBY pin must be pulled up to high. Full documentation is available on the product page.
Features
- Motor voltage (VMOT): 4,5 - 13,5 V
- Logic voltage (VCC): 2,7 - 5,5 V
- Maximum output current: 3.2 A per channel
- Continuous output current: 1.2 A per channel
- Maximum PWM frequency: 100 kHz
- Standby mode
- Built-in thermal protection circuit
- Filter capacitors on both power supply lines
1183405
Data sheet
- Output current
- 1,2 A
- Number of channels
- 2
- Supply voltage min
- 4,5 V
- Supply voltages max
- 13,5 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A set of 40 pieces of female-female connecting cables in various colors, 10 cm long
zł4.31
Delivery date unknown
No product available!
A set of 40 pcs of male-female connecting cables in various colors, 10 cm long
zł4.31
24h
Available quantity: 159
Available
A set of 40 pcs of male-male connecting cables in various colors, 10 cm long
zł5.49
24h
Available quantity: 206
Available
Other products in the same category (16)
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5047
zł406.69
4 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5045
zł456.85
4 weeks
No product available!
ESC RC controller module with FlySky receiver designed for two brush motors with a supply voltage from 2.5 to 5 V and a current consumption of 2 A
zł146.80
24h
Available quantity: 3
Available
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with connectors for assembly. Pololu 5052
zł332.37
4 weeks
No product available!
KAmodMPC17C724 is a module with a double MP bridge bridge type MPC17C724. The system allows you to control two DC brush motors or one bipolar stepping motor. The controller operates at a voltage range of 2.7 - 5.5 V and can work with motors with power consumption up to 0.4 A.
zł19.90
24h
Available quantity: 336
Available
Module with two DRV8830 DC motor drivers. The board is equipped with a Grove connector and communicates via the I2C interface. Seeed Studio 105020010
zł62.29
24h
Available quantity: 1
Available
An H-bridge capable of controlling one DC motor in both directions or two unidirectional motors at voltages from 4.5 to 44 V and continuous current up to 1.1 A. The module offers three operating modes (PH/EN, IN/IN, half-bridge), built-in current limiting and measurement, and protection against overheating, overload, undervoltage, and reverse polarity. Its compact design, flexible logic power supply (1.8–5.5 V), and simple control make it ideal for robotics, automation, and hobby projects. Pololu 4972
zł17.05
24h
Available quantity: 3
Available
Two-channel DC motor driver based on the HR9933 circuit. It allows you to control the movement of drives with a supply voltage of up to 10 V and power consumption up to 1.5 A. DFRobot DRI0040
zł21.46
24h
Available quantity: 9
Available
A single-channel DC motor controller with an I2C interface. It is powered from 1.8 V to 22 V and can deliver up to 1.8 A of current. Board with connectors for assembly. Pololu 5075
zł56.04
24h
Available quantity: 1
Available
Miniature ESC type controller for a DC motor with an input from 3.7 V to 5 V. Offers an additional output current of up to 1.5 A and allows you to control the motor in a channel mixing device
zł64.64
24h
Available quantity: 1
Available
Pololu G2 24v12 High Power is a miniature DC motor controller. Driver\'s power supply: 6.5 ... 30V. Current capacity of the module: 12A. The module has protection against back voltage and overvoltage. Pololu 1365
zł559.49
4 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board with soldered connectors. Pololu 5048
zł354.03
4 weeks
No product available!
This discrete MOSFET H-bridge motor driver enables bidirectional control of one high-power DC brushed motor. The small 1.3×0.8″ board supports a wide 6.5V to 40V voltage range and is efficient enough to deliver a continuous 13A without a heat sink. Driver includes reverse-voltage protection along with basic current sensing and current limiting functionality. Pololu 2992
zł181.07
4 weeks
No product available!
DC motor driver that allows you to control the movement of two drives using the I2C interface. Board without connectors. Pololu 5056
zł575.25
4 weeks
No product available!
DRV8835 Dual Motor Driver Carrier
zł23.90
24h
Available quantity: 4
Available
Dual MAX14870 Motor Driver is a dual DC driver compatible with Raspberry Pi that allows you to control two DC motors with 4.5-36V continuous current of 1.7A. Pololu 3759
zł143.97
24h
Available quantity: 1
Available
Dual motor controller allowing two DC motors to be driven with voltages from 4.5 to 13.5V and a continuous current of 1.2 A per channel. SparkFun ROB-14450