Category: Qwiic peripheral modules (SparkFun)
There are 160 products.
JST-SH 4-pin SMD connector for modules with Qwiic connectors. Pins\' pitch is 1 mm. Qwiic allows you to connect sensors via the I2C bus. SparkFun PRT-16766
End module of the communication system based on QwiicBus. It allows you to extend the range of the I2C bus. SparkFun COM-16988
Shield with Qwiic connectors designed for Raspberry Pi minicomputers. It allows you to easily connect the minicomputer with the Qwiic sensor system. SparkFun DEV-15945
Module with 9-axis IMU ICM-20948 sensor. The chip is an integrated 3-axis accelerometer, gyroscope and magnetometer and a digital motion processor DMP (Digital Motion Processor). Communication via I2C or SPI. SparkFun SEN-15335
Flexible Qwiic cable 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single male goldpin connectors. SparkFun PRT-17912
Module with a voltage level converter 3.3 V - 5 V intended for use in the Qwiic system. It has a built-in Step Up converter providing power supply with a voltage of 5 V and a current of up to 100 mA. SparkFun SPX-17238
Heart rate monitor module based on the popular MAX30101 and MAX32664. The board is equipped with connectors compliant with the Qwiic standard. SparkFun SEN-15219
Flexible Qwiic cable, 150 mm long. On one side it is terminated with a female Qwiic connector, and on the other side with single female goldpin connectors. SparkFun PRT-17261
Module with three optical inspection sensors (spectrophotometers) from the AS7265x series. The module consists of three sensors; AS72651, AS72652 and AS72653 which can detect wavelengths from 410nm (UV) to 940nm (IR). SparkFun SEN-15050
Module with 6-axis IMU LSM6DSO sensor, which combines a 3-axis accelerometer and gyroscope, as well as a 9kB FIFO buffer and event handling functions. Communicates via I2C or SPI. SparkFun SEN-18020
Flexible 4-core cable, 50 mm long, terminated on both sides with a Qwiic plug. Sparkfun PRT-17260
Module with 24-bit ADC NAU7802 converter. It enables reading data from strain gauges and scales. I2C interface. SparkFun SEN-15242
Module with relay up to 5.5 A and 240 V AC controlled by the I2C interface. SparkFun COM-15093
The expansion module is designed to work with Raspberry Pi 400 - a portable computer built into the keyboard. The board has a 40-pin connector in the pin position and two Qwiic connectors. SparkFun DEV-17512
Module with integrated proximity and ambient light sensors and IR emitter in the VCNL4040 system. It allows the detection of obstacles in the range of 0 to 20 cm (no dead zone). It communicates via the I2C bus. SparkFun SEN-15177
Module with BME280 environmental sensor. It allows you to measure temperature, humidity and pressure. The sensor is equipped with two communication interfaces: SPI and I2C (Qwiic). SparkFun SEN-15440
Module with EEPROM memory, capacity 512 kbit (64kB). Communication takes place via the I2C interface. The module has 3 jumpers that enable selection of one of 8 addresses. SparkFun SPX-14764
GPS module with NEO-M9N 92-channel GNSS receiver. The system can receive data from all major positioning systems: GPS, GLONASS, Galileo and BeiDou. It has UART, I2C and SPI interfaces. SparkFun GPS-15712
Air quality sensor module based on SGP30 system. The board has been equipped with Qwiic connectors. SparkFun SEN-16531