New products
New products
Category: Stepper motor controllers
There are 75 products.
A set consisting of a stepper motor driver module based on the ULN2003 system and a stepper motor powered with 5V voltage.
Two-channel DC motor driver powered with the voltage from 2.5 to 12 V with a maximum continuous current of 0.8 A per channel. It can control a bipolar stepper motor
Stepper motor driver that can work with a voltage in the range from 20 to 50 V and a maximum current of 5.6 A. It allows you to configure the microstep in the range from 2 to 128. DM556
Module with TMC2208 stepper motor driver. It enables control with a supply voltage ranging from 5.5 to 34 V and a current of up to 1,2 A
Two-channel driver of direct current (DC) motors with an operating voltage from 4 to 16 V and a maximum continuous current of 3 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron MDD3A
DRV8825 Stepper Motor Driver Carrier is a DRV8825 stepper motor driver that allows you to supply a bipolar current of up to 1.5 A per phase, without using a heat sink. The system can be supplied with voltage up to 45V, in the set there is a heat sink. It is compatible with Polol 2133
Stepper motor driver that can work with a voltage in the range from 20 to 50 V and a maximum current of 4.2 A. It allows you to configure the microstep in the range from 2 to 128. DM542
DRV8711 stepper motor driver module powered by 8-50V voltage and 4A operating current. The controller allows you to control the movement of the engine with up to 9 different resolutions. Configuration via SPI interface. Pololu 3730
A4988 Stepper Motor Driver Carrier with Voltage Regulators
Advanced, compact stepper motor driver with TMC2209 chip that offers smooth, quiet operation, high performance, various operating modes and easy configuration, ideal for 3D printers and other applications. modTMC2209v4
Expansion board with L6474 stepper motor driver. It is equipped with a connector compatible with Arduino Uno R3 and STM32 Nucleo. STMicroelectronics X-NUCLEO-IHM01A1
The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927
This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438
The expansion module is designed to work with micro:bit. It allows you to control 4 DC motors or two stepper motors and 8 servos. It communicates via the I2C interface. DFRobot DFR0548
The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC).
STSPIN220 stepper motor driver module with a low voltage range of 1.8 ... 10V and 1.1A working current. The controller allows you to control the motor motion up to 9 different resolutions (up to 1/256 steps). Pololu 2876
Module with a 2-channel driver for DC motors L293D designed to work with the Raspberry Pi Pico. It can work with a voltage from 6 to 12 V and a current of up to 600 mA. SB Components 21468
Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-MDD10
A4988 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2981
The stepper motor driver with Allegro A4988 (A4988 Stepper Motor Driver Carrier) allows you to supply a bipolar current of up to 2A per phase. The system can be supplied with voltage up to 35V, in the set there is a heat sink. It is compatible with Polol 1182