New products
New products
Category: Communication
Subcategories
There are 555 products.
The dynamic NFC / RFID tag with I2C bus and ISO 15693 RF interface in the SOIC8 housing has a built-in 64k EEPROM memory. Producer: STMicroelectronics
KAmodNFC is an expansion board with M24LR64E-R chip – dynamic tag with 64kb EEPROM memory and dual communication interface (I2C/RF). On board is placed also signalization of energy harvesting function, which is in M24LR64E-R chip embedded.
WiFi 802.11 b/g/n module with ESP8266 system, they have 22 edge terminals with 2 mm raster with the possibility of soldered gold connectors, 9 GPIO lines and 1 ADC line on the connector. Built-in PCB antenna. ESP-12E
KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05
Integrated circuit, combining Wi-Fi functionality and Bluetooth 4.2 BLE. Integrated 32-bit dual-core Xtensa LX6 processor, 448kB ROM, 520kB SRAM. ESP32 allows you to work with many interfaces, including SPI, I2C, UART, CAN, ETH, IR and can be supplied with 2.2V-3.6V. The system has a QFN48 (5x5mm) housing. ESP32-D0WD
NFC module designed for Arduino. Meets the standards of reader mode, P2P mode and card emulation mode. The board has an integrated RF antenna. NXP OM5578/PN7150ARDM
The RFID / NFC transponder reader module (tags) works in the PN532 chip and is compatible with Arduino. Data is available via SPI, I2C or HSU (High Speed UART). Supplied with a RFID card and key ring. ELECHOUSE NFC MODULE V3
SIM800L V2.0 module with support for four-band GSM/GPRS network. Module controlled by AT commands.
The FS1000A transmitter and the MX-RM-5V receiver enable communication in the ISM band; they are easy to use, do not require advanced bus control and have very small dimensions. Especially recommended for work with Arduino and STM32
Miniature Ethernet network module with W5500 chip. It has compact dimensions, so it can be used as an element of another device
External waterproof LPWA antenna dedicated to communication in LoRa networks in the 433 MHz frequency band. It is mounted using the magnet built into the cradle. Waveshare 433/470M Magnet Mount Antenna
WiFi 802.11 b/g/n module with ESP8266 system, 16 terminals are available with a 2 mm pitch with the possibility of soldering gold pins, there are 9 GPIO lines and 1 ADC line on the connector. Built-in ceramic antenna and U.FL antenna connector. ESP-07
The adapter allows you to connect the antenna with a standard 75 Ω connector to the device with the MCX connector. The cable length is 13cm, it is often used in USB DVB-T tuners
Development board D1 Mini with WiFi module ESP-8266MOD and 4 MB Flash memory. The module can be programmed from the Arduino IDE level. WeMos D1 Mini
Antenna with an SMA male connector working in the 433 MHz frequency band. It has a right angle joint
KAmodRPi-GPRS-GPS is an overlay for Raspberry Pi 4 / 3B + / 3B / 2B / B + computers, which allows you to enrich the system with the ability to send data via GPRS, SMS transmission or work as a module for Bluetooth communication. This extension also offers the ability to receive satellite data from location systems - GPS and GLONASS.
The NRF24L01+ chip module for radio communication, which operates in the 2.4 GHz ISM band. It is used in various applications such as wireless sensors, remote control, wireless networks. It supports the Enhanced ShockBurst protocol, which provides automatic packet handling. It communicates via an SPI interface
Demo and programming kit for NFC tags. Designed for emulation using the NTAG I²C plus tag system in embedded systems. NXP NTAG I2C Plus Explorer Kit