Category: STARTER KITS, PROGRAMMERS, MODULES
Kamami.pl electronics store offers a wide range of starter kits for microcontrollers and programmable devices as well as accessories (programmers, modules, etc.).
Subcategories
-
Atmel SAM
-
Atmel Xplain
-
AVR
-
Banana Pi
-
BeagleBone
-
Chiliboard
-
chipKIT
-
CPLD Xilinx
-
Cubieboard
-
DFRobot FireBeetle
-
Analog electronics
-
Feather
-
Alchitry FPGA
-
Altera FPGA
-
Xilinx FPGAs
-
Freedom (Kinetis)
-
FriendlyARM
-
Coral
-
HummingBoard
-
Other development kits
-
Intelligent clothes
-
LattePanda
-
LPC (NXP)
-
M5Stack
-
Micro:bit
-
Peripheral modules
-
Nvidia Jetson
-
Odroid
-
ODYSSEY
-
Orange Pi
-
PIC
-
Segger programmers
-
Serial memory programmers
-
Raisonance
-
Raspberry Pi RP2040
-
RFID
-
RISC-V
-
SBC Embest
-
SBC MYIR
-
SBC UDOO
-
SBC others
-
SoMLabs
-
Sparkfun MicroMod
-
STM32
-
STM32 MP1
-
STM32 Discovery
-
STM32 Nucleo boards
-
STM8
-
Teensy
-
WRTNode
-
Kit with a book
There are 2739 products.
Jarosław Doliński
Marcin Wiązania
Andrzej Pawluczuk
Andrzej Pawluczuk
Robert Wołgajew
Module with the RP2040 microcontroller with two ARM Cortex-M0 + cores operating at 133 MHz, 256 kB RAM and 30 GPIO. The board also has 2 MB of external QSPI flash memory. Module can be programmed in C/C++ or microPython. Raspberry Pi Pico
KAmodWS2812-1 is a module with WS2812 multicolor LED. Thanks to the embedded controller, LED can be series connected to makes an amazing light effects. KAmodWS2812-1
Pin strip straight in black, double-row, female with 2x20 layout, 2.54mm pitch and elongated legs (12mm). Thru-hole assembly (THT), often used to build GPIO modules for single board computers. PBD40S L
Yellow 6-core connecting cable, 30 cm long. Intended for use with Kamami KAmod modules. It is terminated on both sides with a red plug that fits the WF06S connector. CAB_HU06-30-YELLOW
KAmodM41T82 is a module with the STMicroelectronics M41T82 RTC clock. The chip allows precise timing, and an additional battery connector allows you to maintain the power supply when the main power is turned off. Communication with the module is realized via I2C bus.
KAmodLIS35DE is a module with a three-axis LIS35DE accelerator from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows acceleration measurement in three axes.
KAmodLSM303C is a module with the MEMS LSM303C chip from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows measurement of accelerations and magnetic field values in three axes
Module with DS18B20 temperature sensor from Dallas Semiconductor. The sensor used allows you to measure temperatures in the range -55 ~ 125 ° C with an accuracy of ± 0.5 ° C (in the range of -10 ~ 85 ° C). The 1-Wire interface is used for communication. The plate is equipped with a goldpin connector and a KAMAMI connector, allowing easy connection of the module to the commissioning kits.