New products
New products New products
zł74.78
Delivery date unknown
zł43.23
Delivery date unknown
Available
zł119.00
Delivery date unknown
KAmodLIS35DE – module with three-axis accelerometer
ID: 579438
5906623432752
zł19.90
Tax included
zł16.18 tax excl.
KAmodLIS35DE is a module with a three-axis LIS35DE accelerator from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows acceleration measurement in three axes.
Description
KAmodLIS35DE is a module with a three-axis LIS35DE accelerator from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows acceleration measurement in three axes. Thanks to the programmable interrupt generator outputs, it is possible to wake up the microcontroller after detecting free fall or object movement. The board is equipped with a Pmod I2C connector and a KAMAMI connector, allowing easy attachment of the module to development kits. Due to its small dimensions, the product can be used in many development projects, while the Pmod through connector allows the boards to be connected in series.
Features
- LIS35DE (MEMS accelerometer) from STMicroelectronics
- Measuring range: ± 2/± 8 g
- 8-bit data output
- Low power consumption (<1 mW)
- Communication interface: SP /I2C
- Configurable I2C bus address: 0x1C or 0x1D.
- Programmable interrupt generators (with free fall, motion detection)
- Through connector compatible with the Pmod standard, allows for serial connection of Pmod I2C modules
- Connector in accordance with the KAMAMI standard
- Built-in jumpers that enable pull-up on I2C bus lines
- Built-in jumper connecting the INT line of the system to the INT line of the Pmod connectors
- Voltage supply from 1.9 - 3.6 V via the Pmod connector and 1.9 - 5.5 V via the KAMAMI connector
- Mounting holes with a diameter of 2.5 mm
- Dimensions: 61.2 mm x 20.3 mm x 10 mm
579438
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30
zł6.90
24h
Available quantity: 3
Available
Other products in the same category (16)
Module of a stereo 24-bit audio converter with I2S interface (TS4657).
zł59.00
24h
Available quantity: 66
Available
A 30 cm long connecting cable (6 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF06S connector that KAmod modules are equipped with. cabhu06-30
zł9.90
24h
Available quantity: 192
Available
Relay output module for Raspberry Pi 4B, Pi 3B+ Pi3B, Pi2, Pi+, Pi minicomputers.
zł49.00
24h
Available quantity: 140
Available
Module with digital thermal sensor, thermostat and I2C interface
zł19.90
24h
Available quantity: 189
Available
Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.
zł99.00
24h
Available quantity: 36
Available
Module with L3G4200D (3-axis gyroscope with digital output)
zł34.90
24h
Available quantity: 2
Available
KAmodPCA9533 is a module with LED driver from NXP. The module allows you to control the brightness of 4 LEDs using programmable PWM signals (with a frequency from 0.591 Hz to 152 Hz). I2C interface. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector
zł21.89
24h
Available quantity: 214
Available
Module with DS18B20 temperature sensor from Dallas Semiconductor. The sensor used allows you to measure temperatures in the range -55 ~ 125 ° C with an accuracy of ± 0.5 ° C (in the range of -10 ~ 85 ° C). The 1-Wire interface is used for communication. The plate is equipped with a goldpin connector and a KAMAMI connector, allowing easy connection of the module to the commissioning kits.
zł13.90
24h
Available quantity: 369
Available
Pressure sensor module with I2C interface (BMP085)
zł74.89
24h
Available quantity: 5
Available
KAmodMAG3110FC is a module with magnetic field sensor MAG3110FC from NXP. The sensor measures the magnetic field in the range of ±1000μT, with a resolution of 0.1μT. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMAG3110FC
zł24.90
24h
Available quantity: 335
Available
zł5.90
24h
Available quantity: 480
Available
Available
Available
Yellow 6-core connecting cable, 30 cm long. Intended for use with Kamami KAmod modules. It is terminated on both sides with a red plug that fits the WF06S connector. CAB_HU06-30-YELLOW
Regular pricezł5.90zł1.89
24h
Available quantity: 493
Available
KAmodVL6180X is a module that allows to measure light intensity (ALS), distance to the object and recognition of gesture. It has an embedded voltage regulator and voltage level translators on signal lines. Thanks to this can be used in systems with 2.8...5.5V power supply voltage.
zł39.00
24h
Available quantity: 270
Available
KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.
zł39.90
24h
Available quantity: 86
Available
KAmodLIS35DE is a module with a three-axis LIS35DE accelerator from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows acceleration measurement in three axes.