KAmodMIC_ELECTRET - microphone module with embedded amplifier
ID: 558041
5906623433247
zł10.90
Tax included
zł8.86 tax excl.
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
Description
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
Features
- Microphone KPCM6B-P type from KEPO
- Embedded LMV321L amplifier from STMicroelectronics
- Rail-to-rail amplifier type with hundredfold amplification of signal from microphone
- Power supply voltage: 2.7...6V
- Output voltage of module in silence is equal to a half of power supply voltage
- Embedded low-pass filter with cutoff frequency 10.6kHz
- Place for soldering of pin header
- Mounting holes 3mm
- Module size (without connector): 22.5mm x 9.3mm x 8mm
Application example (board KAmodMIC_ELECTRET connected to KAmduino UNO)
An Arduino example program using the module KAmodMIC_ELECTRET can be found in the article "Arduino and electret microphone" on the blog hobbyspace.pl.
An Arduino example program using the KAmodMIC_ELECTRET module can be found in the article "Arduino - LED control indicator" on the blog hobbyspace.pl.
Kit content
- KAmodMIC_MEMS module
- 3-Pin header (male straight and angled) for soldering
558041
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knocks or any sounds loud enough to be picked up by a microcontroller’s analog-to-digital converter. Each breakout comes fully assembled and works from 2.7V up to 5.5V. BOB-12758
zł46.49
24h
Available quantity: 1
Available
Other products in the same category (16)
Module with digital thermal sensor, thermostat and I2C interface
zł19.90
24h
Available quantity: 189
Available
A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30
zł6.90
24h
Available quantity: 3
Available
A 30 cm long connecting cable (6 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF06S connector that KAmod modules are equipped with. cabhu06-30
zł9.90
24h
Available quantity: 192
Available
Available
Available
RJ12 6-Pin PH 10-Pin IDC Adapter for PIC Microcontrollers Programming
zł25.90
24h
Available quantity: 41
Available
Available
Available
Available
Available
Available
The KAmodRS module is a reliable RS232-UART converter supporting voltages from 3 V to 5.5 V and enabling data transmission at a speed of up to 250 kbit/s. Thanks to the use of the MAX3232 chip, the module is ideal for a wide range of electronic and microcontroller applications requiring stable and effective serial communication
zł15.99
24h
Available quantity: 117
Available
Pressure sensor module with I2C interface (MPL115A2)
zł44.90
24h
Available quantity: 19
Available
Module of a stereo 24-bit audio converter with I2S interface (TS4657).
zł59.00
24h
Available quantity: 66
Available
Module with AT42QT1060 controller - contectless keyboard controller, Kamami, RoHS.
zł89.00
24h
Available quantity: 185
Available
Pressure sensor module with I2C interface (BMP085)
zł74.89
24h
Available quantity: 5
Available
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.