KAmodPH

Expander (overlay) extending the functionality of the STM32 Nucleo development board. Shield has ST Morpho connectors and is equipped with in a four-segment 7-segment display, four RGB diodes, LIS35DE accelerometer, LPS25HB pressure sensor, and DS18B20 digital thermometer

KAmodVL6180X is a module that allows to measure light intensity (ALS), distance to the object and recognition of gesture. It has an embedded voltage regulator and voltage level translators on signal lines. Thanks to this can be used in systems with 2.8...5.5V power supply voltage.

KAmodMC3635 is a module with the MC3635 three-axis accelerometer from mCube. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g/±12g/±16g, the measurement frequency is from 14 to 1300 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMC3635

Module with Nokia 6100/6610 color graphic LCD

Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.

Programmable RGB and RGBA LED driver

KAmodMMA8451Q is a module with the MMA8451Q three-axis accelerometer from NXP. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMMA8451Q

KAmodRPi-GPRS-GPS is an overlay for Raspberry Pi 4 / 3B + / 3B / 2B / B + computers, which allows you to enrich the system with the ability to send data via GPRS, SMS transmission or work as a module for Bluetooth communication. This extension also offers the ability to receive satellite data from location systems - GPS and GLONASS.

KAmodPCA9533 is a module with LED driver from NXP. The module allows you to control the brightness of 4 LEDs using programmable PWM signals (with a frequency from 0.591 Hz to 152 Hz). I2C interface. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector

KAmodLSM303C is a module with the MEMS LSM303C chip from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows measurement of accelerations and magnetic field values in three axes

KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2

KAmodMPC17C724 is a module with a double MP bridge bridge type MPC17C724. The system allows you to control two DC brush motors or one bipolar stepping motor. The controller operates at a voltage range of 2.7 - 5.5 V and can work with motors with power consumption up to 0.4 A.

Simulation set for Siemens S7-1200 PLC devices. Using this set, it is possible to verify the operation of a program written for a PLC by applying the appropriate states to the digital inputs, to the analogue (ADC) inputs voltages from the built-in or external sensors. LED status monitoring is possible

KAmodMMA8653FC is a module with NXP's MMA8653FC three-axis accelerometer. The sensor allows the measurement of acceleration in the range of ± 2g / ± 4g / ± 8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor takes place via the I2C interface

Pressure sensor module with I2C interface (MPL115A2)

KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.