zł75.53 tax excl.
Expander (overlay) extending the functionality of the STM32 Nucleo development board. Shield has ST Morpho connectors and is equipped with in a four-segment 7-segment display, four RGB diodes, LIS35DE accelerometer, LPS25HB pressure sensor, and DS18B20 digital thermometer
Expander (overlay) extending the functionality of the STM32 Nucleo 64 development board. Shield has ST Morpho connectors and is equipped with, among others, in a four-character 7-segment display, four RGB diodes, LIS35DE accelerometer (MEMS), LPS25HB pressure sensor (MEMS), and a DS18B20 temperature sensor.

Manufacturer
Responsible person
STM32 Nucleo development board for STM32 F1 series - with STM32F103RBT6 MCU, 128KB flash memory, STM, RoHS
STM32 Nucleo development board for STM32 F4 series - with STM32F401RE MCU, 512KB flash memory, STM, RoHS
No product available!
STM32 Nucleo development board for STM32 F0 series - with STM32F030R8T6 MCU, 64KB flash memory, STM, RoHS
STM32 Nucleo development board for STM32 L1 series - with STM32L152RE MCU, 512KB flash memory, STM, RoHS
STM32 Nucleo development board for STM32 L0 series - with STM32L053R8 MCU, 64KB flash memory, STM, RoHS
STM32 Nucleo development board for STM32 F3 series - with STM32F302R8 MCU, 64KB flash memory, STM, RoHS
STM32 Nucleo development board for STM32 F3 series - with STM32F334R8T6 MCU, 64KB flash memory, STM, RoHS
STM32 Nucleo development board for STM32 F4 series - with STM32F411RE MCU, 512KB flash memory, STM, RoHS
No product available!
STM32 Nucleo development board for STM32 F0 series - with STM32F072RBT6 MCU, 128KB flash memory, STM, RoHS
STM32 Nucleo-64 development board with STM32F303RET6 MCU, supports Arduino and ST morpho connectivity
Starter kit from the NUCLEO series equipped with the STM32F070RBT6 microcontroller (128 KB Flash, Cortex-M0), with a built-in programmer-debugger ST-Link/V2, equipped with connectors compatible with Arduino.
STM32 Nucleo-64 development board with STM32L476RGT6 MCU, supports Arduino and ST morpho connectivity
Module with L3G4200D (3-axis gyroscope with digital output)
Relay output module for Raspberry Pi 4B, Pi 3B+ Pi3B, Pi2, Pi+, Pi minicomputers.
Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.
KAmodL3GD20 is a digital gyroscope module with L3GD20 chip. It makes possible to measure angular velocity up to ± 2000 degrees per second. It has a embedded voltage regulator and level translators on SDA/SCL lines, thanks to which it can be used in systems supplied with a voltage of 2.5 V-5.5 V. KAmodL3GD20
KAmodNFC is an expansion board with M24LR64E-R chip – dynamic tag with 64kb EEPROM memory and dual communication interface (I2C/RF). On board is placed also signalization of energy harvesting function, which is in M24LR64E-R chip embedded.
KAmodLPS25HB is a module that allows the measurement of atmospheric pressure in the range of 260-1260hPa with a resolution of 0.01hPa, and thanks to the embedded regulator and voltage translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V.
KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05
KAmodMMA7361LC is an accelerometer module with an analogue output, equipped with the MMA7361LC chip. It has a embedded voltage regulator, so it can be used in systems supplied with voltage of 2.5...5.5V.
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
KAmodWS2812-1 is a module with WS2812 multicolor LED. Thanks to the embedded controller, LED can be series connected to makes an amazing light effects. KAmodWS2812-1
KAmodHTS221 is a module that allows the measurement of humidity and temperature, and thanks to the built-in stabilizer and translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V
KAmodVL6180X is a module that allows to measure light intensity (ALS), distance to the object and recognition of gesture. It has an embedded voltage regulator and voltage level translators on signal lines. Thanks to this can be used in systems with 2.8...5.5V power supply voltage.
ZL5USB is a USB-UART converter module based on Silabs CP2102. The module has small sizes, microUSB connector and it can works with the 2.5...5.5V signals.
Expander (overlay) extending the functionality of the STM32 Nucleo development board. Shield has ST Morpho connectors and is equipped with in a four-segment 7-segment display, four RGB diodes, LIS35DE accelerometer, LPS25HB pressure sensor, and DS18B20 digital thermometer
No product available!
KAmodLSM303C is a module with the MEMS LSM303C chip from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows measurement of accelerations and magnetic field values in three axes
KAmodLSM6DS3 is a module that allows measurement of acceleration and angular velocity values. It has a built-in voltage stabilizer and level translators on SDA / SCL lines, thanks to which it can be used in 2.5-5.5V voltage systems
Expander (overlay) extending the functionality of the STM32 Nucleo development board. Shield has ST Morpho connectors and is equipped with in a four-segment 7-segment display, four RGB diodes, LIS35DE accelerometer, LPS25HB pressure sensor, and DS18B20 digital thermometer