KAmodL3GD20 - MEMS gyroscope module with L3GD20 chip from STMicroelectronics

KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2

KAmodMMA8451Q is a module with the MMA8451Q three-axis accelerometer from NXP. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMMA8451Q

KAmodMAG3110FC is a module with magnetic field sensor MAG3110FC from NXP. The sensor measures the magnetic field in the range of ±1000μT, with a resolution of 0.1μT. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMAG3110FC

KAmodRPi-GPRS-GPS is an overlay for Raspberry Pi 4 / 3B + / 3B / 2B / B + computers, which allows you to enrich the system with the ability to send data via GPRS, SMS transmission or work as a module for Bluetooth communication. This extension also offers the ability to receive satellite data from location systems - GPS and GLONASS.

KAmodRPi-Pmod-HAT is a HAT for Raspberry Pi 5/4B/3B+/3B/2B/B+ minicomputers that allows use of the communication interfaces available on the 40-pin minicomputer connector

Module with NXP temperature sensor. It allows you to measure temperature in the range from -55 °C to +125 °C. I2C interface. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector

KAmodMMA8653FC is a module with NXP's MMA8653FC three-axis accelerometer. The sensor allows the measurement of acceleration in the range of ± 2g / ± 4g / ± 8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor takes place via the I2C interface

Module with DS18B20 temperature sensor from Dallas Semiconductor. The sensor used allows you to measure temperatures in the range -55 ~ 125 ° C with an accuracy of ± 0.5 ° C (in the range of -10 ~ 85 ° C). The 1-Wire interface is used for communication. The plate is equipped with a goldpin connector and a KAMAMI connector, allowing easy connection of the module to the commissioning kits.

KAmodPCA9533 is a module with LED driver from NXP. The module allows you to control the brightness of 4 LEDs using programmable PWM signals (with a frequency from 0.591 Hz to 152 Hz). I2C interface. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector

KAmodM41T82 is a module with the STMicroelectronics M41T82 RTC clock. The chip allows precise timing, and an additional battery connector allows you to maintain the power supply when the main power is turned off. Communication with the module is realized via I2C bus.

KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.

Module with a 4-bit bi-directional voltage level converter. It allows you to connect digital interfaces with different operating voltages. KAmodNTS0104PW

KAmodLIS35DE is a module with a three-axis LIS35DE accelerator from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows acceleration measurement in three axes.

Yellow 6-core connecting cable, 30 cm long. Intended for use with Kamami KAmod modules. It is terminated on both sides with a red plug that fits the WF06S connector. CAB_HU06-30-YELLOW

Four relay output module for Raspberry Pi 4B, Pi 3B+ Pi3B, Pi2, Pi+, Pi minicomputers.