![KAmodNFC - ekspander z wbudowanym tagiem NFC/RFID, kompatybilny z Arduino oraz NUCLEO KAmodNFC - ekspander z wbudowanym tagiem NFC/RFID, kompatybilny z Arduino oraz NUCLEO](https://kamami.pl/23297-large_default/kamodnfc-an-expander-with-nfcrfid-compatible-with-arduino-and-nucleo.jpg)
![KAmodNFC - ekspander z wbudowanym tagiem NFC/RFID, kompatybilny z Arduino oraz NUCLEO KAmodNFC - ekspander z wbudowanym tagiem NFC/RFID, kompatybilny z Arduino oraz NUCLEO](https://kamami.pl/23297-large_default/kamodnfc-an-expander-with-nfcrfid-compatible-with-arduino-and-nucleo.jpg)
zł23.50 tax excl.
KAmodNFC is an expansion board with M24LR64E-R chip – dynamic tag with 64kb EEPROM memory and dual communication interface (I2C/RF). On board is placed also signalization of energy harvesting function, which is in M24LR64E-R chip embedded.
free shipping in Poland for all orders over 500 PLN
If your payment will be credited to our account by 11:00
Each consumer can return the purchased goods within 14 days
KAmodNFC is an expansion board with M24LR64E-R chip – dynamic tag with 64kb EEPROM memory and dual communication interface (I2C/RF). On board is placed also signalization of energy harvesting function, which is in M24LR64E-R chip embedded.
Application example (KAmodNFC board connected to the KAmduino UNO):
![]() |
![]() |
Development kit containing the M24LR04E-R EEPROM chip. It consists of two ready-to-use boards that can communicate with each other via the I2C or RFID bus.
No product available!
Demonstration kit for M24LRxx Dual Interface EEPROMs, STM, RoHS
Development kit for ST Dual Interface EEPROM (M24LRxx-R), STM, RoHS
Development board with dimensions and spacing compatible with Arduino Uno R3. It have built-in Wi-Fi ESP8266 module. The device is compatible with WeDOS D1, it can be programmed from the level of Arduino IDE
The X-NUCLEO-NFC02A1 is a dynamic NFC/RFID tag board based on M24LR04E-R, for expansion of STM32 Nucleo boards
KAmodHTS221 is a module that allows the measurement of humidity and temperature, and thanks to the built-in stabilizer and translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V
KAmodMMA8653FC is a module with NXP's MMA8653FC three-axis accelerometer. The sensor allows the measurement of acceleration in the range of ± 2g / ± 4g / ± 8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor takes place via the I2C interface
KAmodRPi-Pmod-HAT is a HAT for Raspberry Pi 5/4B/3B+/3B/2B/B+ minicomputers that allows use of the communication interfaces available on the 40-pin minicomputer connector
KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05
KAmodL3GD20 is a digital gyroscope module with L3GD20 chip. It makes possible to measure angular velocity up to ± 2000 degrees per second. It has a embedded voltage regulator and level translators on SDA/SCL lines, thanks to which it can be used in systems supplied with a voltage of 2.5 V-5.5 V. KAmodL3GD20
KAmodM41T82 is a module with the STMicroelectronics M41T82 RTC clock. The chip allows precise timing, and an additional battery connector allows you to maintain the power supply when the main power is turned off. Communication with the module is realized via I2C bus.
KAmodQTR8A is a module with eight photointerrupter sensors KTIR0711S. It allows to detect edge or line. Thanks to the analog outputs, is possible to connect a module to the e.g. comparator. The module can be used in analisze of the floor e.g. by Linefollower vehicles.
Module with a 4-bit bi-directional voltage level converter. It allows you to connect digital interfaces with different operating voltages. KAmodNTS0104PW
KAmodVL6180X is a module that allows to measure light intensity (ALS), distance to the object and recognition of gesture. It has an embedded voltage regulator and voltage level translators on signal lines. Thanks to this can be used in systems with 2.8...5.5V power supply voltage.
KAmodLSM6DS3 is a module that allows measurement of acceleration and angular velocity values. It has a built-in voltage stabilizer and level translators on SDA / SCL lines, thanks to which it can be used in 2.5-5.5V voltage systems
KAmodLPS25HB is a module that allows the measurement of atmospheric pressure in the range of 260-1260hPa with a resolution of 0.01hPa, and thanks to the embedded regulator and voltage translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V.
KAmodMAG3110FC is a module with magnetic field sensor MAG3110FC from NXP. The sensor measures the magnetic field in the range of ±1000μT, with a resolution of 0.1μT. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMAG3110FC
KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.
KAmodNFC is an expansion board with M24LR64E-R chip – dynamic tag with 64kb EEPROM memory and dual communication interface (I2C/RF). On board is placed also signalization of energy harvesting function, which is in M24LR64E-R chip embedded.