KAmodMEMS2

KAmodMMA7361LC is an accelerometer module with an analogue output, equipped with the MMA7361LC chip. It has a embedded voltage regulator, so it can be used in systems supplied with voltage of 2.5...5.5V.

KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.

KAmodWS2812-1 is a module with WS2812 multicolor LED. Thanks to the embedded controller, LED can be series connected to makes an amazing light effects. KAmodWS2812-1

KAmodHTS221 is a module that allows the measurement of humidity and temperature, and thanks to the built-in stabilizer and translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V

KAmodVL6180X is a module that allows to measure light intensity (ALS), distance to the object and recognition of gesture. It has an embedded voltage regulator and voltage level translators on signal lines. Thanks to this can be used in systems with 2.8...5.5V power supply voltage.

ZL5USB is a USB-UART converter module based on Silabs CP2102. The module has small sizes, microUSB connector and it can works with the 2.5...5.5V signals.

Expander (overlay) extending the functionality of the STM32 Nucleo development board. Shield has ST Morpho connectors and is equipped with in a four-segment 7-segment display, four RGB diodes, LIS35DE accelerometer, LPS25HB pressure sensor, and DS18B20 digital thermometer

KAmodLSM303C is a module with the MEMS LSM303C chip from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows measurement of accelerations and magnetic field values in three axes

KAmodLSM6DS3 is a module that allows measurement of acceleration and angular velocity values. It has a built-in voltage stabilizer and level translators on SDA / SCL lines, thanks to which it can be used in 2.5-5.5V voltage systems

KAmodMPC17C724 is a module with a double MP bridge bridge type MPC17C724. The system allows you to control two DC brush motors or one bipolar stepping motor. The controller operates at a voltage range of 2.7 - 5.5 V and can work with motors with power consumption up to 0.4 A.

KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2

KAmodMMA8451Q is a module with the MMA8451Q three-axis accelerometer from NXP. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMMA8451Q

KAmodMAG3110FC is a module with magnetic field sensor MAG3110FC from NXP. The sensor measures the magnetic field in the range of ±1000μT, with a resolution of 0.1μT. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMAG3110FC

KAmodRPi-GPRS-GPS is an overlay for Raspberry Pi 4 / 3B + / 3B / 2B / B + computers, which allows you to enrich the system with the ability to send data via GPRS, SMS transmission or work as a module for Bluetooth communication. This extension also offers the ability to receive satellite data from location systems - GPS and GLONASS.

KAmodRPi-Pmod-HAT is a HAT for Raspberry Pi 5/4B/3B+/3B/2B/B+ minicomputers that allows use of the communication interfaces available on the 40-pin minicomputer connector

Module with NXP temperature sensor. It allows you to measure temperature in the range from -55 °C to +125 °C. I2C interface. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector