

zł22.68 tax excl.
KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2
KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector, that allow to easy connection of the module to the evaluation kits. Due to its small dimensions, the product can be used in many development projects, while the Pmod connector allows to connect the boards in the series.
Data sheet
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Pressure sensor module with I2C interface (MPL115A2)
Pressure sensor module with I2C interface (BMP085)
KAmodLPS25HB is a module that allows the measurement of atmospheric pressure in the range of 260-1260hPa with a resolution of 0.01hPa, and thanks to the embedded regulator and voltage translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V.
KAmodLPS331 is a module that allows the measurement of atmospheric pressure in the range of 260 - 1260 hPa with a resolution of 0.02 hPa. Supply voltage 2.5 - 5.5 V,
Small 10 DoF IMU module with 3-axis gyroscope and accelerometer (LSM6DSO), 3-axis magnetometer (LIS3MDL) and barometer (LPS22DF). It is equipped with an I2C interface, a voltage stabilizer and a voltage level converter. Pololu 2863
Multifunctional expander (shield) for NUCLEO and Arduino equipped with Bluetooth 2.0+EDR (HC-05) interface, MEMS 3DoF LIS35, LED-RGB, joystick and analog STLM20 temperature sensor developed and produced by KAMAMI.
KAmodL3GD20 is a digital gyroscope module with L3GD20 chip. It makes possible to measure angular velocity up to ± 2000 degrees per second. It has a embedded voltage regulator and level translators on SDA/SCL lines, thanks to which it can be used in systems supplied with a voltage of 2.5 V-5.5 V. KAmodL3GD20
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
KAmodRPi-GPRS-GPS is an overlay for Raspberry Pi 4 / 3B + / 3B / 2B / B + computers, which allows you to enrich the system with the ability to send data via GPRS, SMS transmission or work as a module for Bluetooth communication. This extension also offers the ability to receive satellite data from location systems - GPS and GLONASS.
KAmodMPC17C724 is a module with a double MP bridge bridge type MPC17C724. The system allows you to control two DC brush motors or one bipolar stepping motor. The controller operates at a voltage range of 2.7 - 5.5 V and can work with motors with power consumption up to 0.4 A.
KAmodQTR8A is a module with eight photointerrupter sensors KTIR0711S. It allows to detect edge or line. Thanks to the analog outputs, is possible to connect a module to the e.g. comparator. The module can be used in analisze of the floor e.g. by Linefollower vehicles.
KAmodRPi-Pmod-HAT is a HAT for Raspberry Pi 5/4B/3B+/3B/2B/B+ minicomputers that allows use of the communication interfaces available on the 40-pin minicomputer connector
KAmodHTS221 is a module that allows the measurement of humidity and temperature, and thanks to the built-in stabilizer and translator levels, it can be successfully used in systems supplied with a voltage of 2.5 - 5.5 V
KAmodM41T82 is a module with the STMicroelectronics M41T82 RTC clock. The chip allows precise timing, and an additional battery connector allows you to maintain the power supply when the main power is turned off. Communication with the module is realized via I2C bus.
KAmodMMA7361LC is an accelerometer module with an analogue output, equipped with the MMA7361LC chip. It has a embedded voltage regulator, so it can be used in systems supplied with voltage of 2.5...5.5V.
Four relay output module for Raspberry Pi 4B, Pi 3B+ Pi3B, Pi2, Pi+, Pi minicomputers.
A 30 cm long connecting cable (6 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF06S connector that KAmod modules are equipped with. cabhu06-30
KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2