KAmodPCF8883T – module with capacitive touch sensor
ID: 576065
5906623432721
zł19.90
Tax included
zł16.18 tax excl.
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.
Description
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The board is equipped with a Pmod GPIO standard connector with one digital output informing about the status of the sensor output depending on the selected mode of operation and a KAMAMI connector, allowing easy connection of the module to development kits. The module has a probe placed on the PCB and a diode indicating the state of the chip. Due to its small dimensions, the product can be used in many development projects.
The module is equipped with jumpers enabling configuration of the system's operating mode. One of three jumpers may be on. Allows you to select the system operation in the mode:
- PB (Push Button) - the output is high as long as the probe event occurs
- PUL (Pulse) - the event is active for 1 second after the event occurs on the probe
- TOG (Toggle) - the occurrence of an event on the probe causes a change in the state on the output pin
Features
- NXP PCF8883T system
- Dynamic proximity sensor
- Wide input capacity range
- Automatic calibration
- Configurable operating mode (push-button, toggle, pulse)
- Wide operating temperature range: -40oC to +85oC
- Probe placed on the PCB
- Diode signaling the status of the OUT output
- Connector compatible with the Pmod GPIO standard
- Connector in accordance with the KAMAMI standard
- Built-in jumpers for selecting the system operation mode
- Can be supplied with voltage from 3 to 9 V
- Mounting holes with a diameter of 2.5 mm
- Dimensions: 51.3 mm x 20.3 mm x 10 mm
576065
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30
zł6.90
24h
Available quantity: 3
Available
Capacitive 8-channel proximity switch with auto-calibration and very low power consumption, TSSOP28, NXP, RoHS
zł18.92
24h
Available quantity: 4
Available
Set of 40 pieces of male-female connection cables, in various colors, 17 cm long. CAB_M-F (Rainbow-40-17)
zł5.97
24h
Available quantity: 32
Available
A set of 40 female-female connection cables, in various colors, 17 cm long. CAB_F-F (Rainbow-40-17)
zł5.69
24h
Available quantity: 117
Available
Other products in the same category (16)
KAmodL3GD20 is a digital gyroscope module with L3GD20 chip. It makes possible to measure angular velocity up to ± 2000 degrees per second. It has a embedded voltage regulator and level translators on SDA/SCL lines, thanks to which it can be used in systems supplied with a voltage of 2.5 V-5.5 V. KAmodL3GD20
zł39.90
24h
Available quantity: 100
Available
KAmodMIC_ELECTRET is a module with microphone KPCM6B type. Thanks to embedded amplifier with hundredfold amplification of signal, output voltage can be measurement in microcontroller with using e.g. ADC converter.
zł10.90
24h
Available quantity: 135
Available
KAmodRPi-Pmod-HAT is a HAT for Raspberry Pi 5/4B/3B+/3B/2B/B+ minicomputers that allows use of the communication interfaces available on the 40-pin minicomputer connector
zł42.90
24h
Available quantity: 260
Available
Module with AT42QT1060 controller - contectless keyboard controller, Kamami, RoHS.
zł89.00
24h
Available quantity: 185
Available
Pressure sensor module with I2C interface (MPL115A2)
zł44.90
24h
Available quantity: 19
Available
A 30 cm long connecting cable (6 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF06S connector that KAmod modules are equipped with. cabhu06-30
zł9.90
24h
Available quantity: 192
Available
Available
KAmodMMA7361LC is an accelerometer module with an analogue output, equipped with the MMA7361LC chip. It has a embedded voltage regulator, so it can be used in systems supplied with voltage of 2.5...5.5V.
zł28.91
24h
Available quantity: 192
Available
Available
RJ12 6-Pin PH 10-Pin IDC Adapter for PIC Microcontrollers Programming
zł25.90
24h
Available quantity: 43
Available
The KAmodRS module is a reliable RS232-UART converter supporting voltages from 3 V to 5.5 V and enabling data transmission at a speed of up to 250 kbit/s. Thanks to the use of the MAX3232 chip, the module is ideal for a wide range of electronic and microcontroller applications requiring stable and effective serial communication
zł15.99
24h
Available quantity: 120
Available
Relay output module for Raspberry Pi 4B, Pi 3B+ Pi3B, Pi2, Pi+, Pi minicomputers.
zł49.00
24h
Available quantity: 140
Available
Available
zł5.90
24h
Available quantity: 480
Available
Pressure sensor module with I2C interface (BMP085)
zł74.89
24h
Available quantity: 5
Available
KAmodMAG3110FC is a module with magnetic field sensor MAG3110FC from NXP. The sensor measures the magnetic field in the range of ±1000μT, with a resolution of 0.1μT. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMAG3110FC
zł24.90
24h
Available quantity: 335
Available
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.