KAmodLM75A – module with temperature sensor
ID: 572188
5906623432677
zł17.90
Tax included
zł14.55 tax excl.
Module with NXP temperature sensor. It allows you to measure temperature in the range from -55 °C to +125 °C. I2C interface. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector
Description
KAmodLM75A is a module with a NXP temperature sensor. It allows you to measure temperature in the range from -55 °C to +125 °C. Communication with the sensor is realized via the I2C interface. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector, allowing easy attachment of the module to development kits. Due to its small dimensions, the product can be used in many development projects, while the Pmod through connector allows the boards to be connected in series.
Features
- LM75A chip from NXP
- I2C bus interface with up to 8 devices on the same bus (address configuration via jumpers)
- Temperature measurement in the range from -55 °C to +125 °C
- 11-bit ADC converter with a resolution of 0.125 °C
- Accuracy of temperature measurement:
- ± 2 °C from -25 °C to +100 °C
- ± 3 °C from -55 °C to +125 °C
- Programmable temperature thresholds and hysteresis setpoints
- 3.5 µA supply current in off mode to save power
- Independent work as a thermostat when switching on
- Protection against electrostatic discharge
- Through connector compatible with the Pmod standard, allows for serial connection of Pmod I2C modules
- Connector compatible with the KAMAMI standard
- Embedded jumpers that enable pull-up on I2C bus lines
- Supply range from 2.8 V to 5.5 V
- Mounting holes with a diameter of 2.5 mm
- Dimensions: 61.2 x 20.3 x 10 mm
572188
Data sheet
- Interface
- I2C
- Type of sensor
- LM75A
- Power supply voltage
- 2,8 - 5,5 V
- Sensor type
- Temperatury
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2
zł27.90
24h
Available quantity: 192
Available
KAmodMAG3110FC is a module with magnetic field sensor MAG3110FC from NXP. The sensor measures the magnetic field in the range of ±1000μT, with a resolution of 0.1μT. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMAG3110FC
zł24.90
24h
Available quantity: 335
Available
KAmodMMA8653FC is a module with NXP's MMA8653FC three-axis accelerometer. The sensor allows the measurement of acceleration in the range of ± 2g / ± 4g / ± 8g, the measurement frequency is from 1.56 Hz to 800 Hz. Communication with the sensor takes place via the I2C interface
zł26.90
24h
Available quantity: 459
Available
Module with DS18B20 temperature sensor from Dallas Semiconductor. The sensor used allows you to measure temperatures in the range -55 ~ 125 ° C with an accuracy of ± 0.5 ° C (in the range of -10 ~ 85 ° C). The 1-Wire interface is used for communication. The plate is equipped with a goldpin connector and a KAMAMI connector, allowing easy connection of the module to the commissioning kits.
zł13.90
24h
Available quantity: 367
Available
Other products in the same category (16)
STEMMA QT SHT45 Precision Temperature & Humidity Sensor - SHT45 Temperature & Humidity Sensor Module
A digital temperature and humidity sensor module based on the SHT45 chip. It features a STEMMA QT/Qwiic connector and communicates via an I2C interface. Adafruit 5665
zł62.66
24h
Available quantity: 1
Available
ST Microelectronics’ STTS22H digital temperature sensor module, featuring a Qwiic connector, offers accuracy from -40°C to 125°C without the need for additional calibration. The sensor consumes only 1.75 µA in single measurement mode, making it ideal for low-power applications, and additional features such as a configurable interrupt pin and the ability to select two I2C addresses increase its versatility. SparkFun SEN-21262
zł31.48
24h
Available quantity: 1
Available
ST Microelectronics’ STTS22H digital temperature sensor module, featuring a Qwiic connector, offers accuracy from -40°C to 125°C without the need for additional calibration. The sensor consumes only 1.75 µA in single measurement mode, making it ideal for low-power applications, and additional features such as a configurable interrupt pin and the ability to select two I2C addresses increase its versatility. SparkFun SEN-21273
zł34.97
24h
Available quantity: 2
Available
The AHT25 is a versatile and precise humidity and temperature measurement module, ideal for consumer electronics and industrial applications.
zł10.86
24h
Available quantity: 34
Available
The AHT15 is a precise and reliable temperature and humidity sensor, ideal for applications in harsh environmental conditions.
zł17.72
24h
Available quantity: 1
Available
The AM2315C is an advanced packaged temperature and humidity sensor offering easy integration with microcontrollers thanks to its 2.5V-5.5V power supply and standard I2C interface, providing greater resistance to external conditions than typical SHT sensors, with measurement accuracy of ±2% RH and ±0.3°C
zł79.00
24h
Available quantity: 19
Available
Temperature sensor based on a DS18B20 chip replacement. It is enclosed in a waterproof measuring probe. It has a 2 m cable and communicates via a 1-Wire interface
zł11.66
4 weeks
No product available!
Temperature sensor based on the DS18B20 chip. It is enclosed in a waterproof measuring probe. It has a 2 m cable and communicates via a 1-Wire interface
zł15.95
4 weeks
No product available!
The AM2301A temperature and humidity sensor is designed to measure in a variety of environmental conditions. It offers a measuring range of temperature from -40 to +80 °C and humidity from 0 to 100%RH. AM2301A
zł19.48
4 weeks
No product available!
Module with 3-axis accelerometer ADXL343 and precise temperature sensor ADT7410 dedicated to Feather series boards. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4147
zł62.29
24h
Available quantity: 2
Available
A digital temperature and humidity sensor module based on the SHT41 chip. It features a STEMMA QT/Qwiic connector and communicates via an I2C interface. Adafruit 5776
zł31.08
24h
Available quantity: 5
Available
Module with a thermal imaging camera with an 80x42 field matrix and a 45° viewing angle. It is dedicated to work with the Raspberry Pi minicomputer and communicates via the SPI interface. Waveshare Thermal USB Camera
zł355.27
24h
Available quantity: 4
Available
Analog PT1000 temperature sensor with a wide measurement range from -50°C to 300°C. High sensitivity allows for quick response to temperature changes. It is an excellent choice for many industrial applications. Seeed Studio 314010819
zł52.96
24h
Available quantity: 5
Available
A USB thermal camera module for Raspberry Pi offering precise temperature detection with a resolution of 80×62 pixels. It enables easy integration into industrial applications and control systems. It is an ideal solution for temperature monitoring, thermal analysis and security systems. Waveshare Thermal-90 USB Camera
zł618.91
4 weeks
No product available!
Thermal camera module for Raspberry Pi offering precise temperature detection with 80x62 pixel resolution. It enables easy integration into industrial applications and control systems. It is ideal for temperature monitoring, thermal analysis and security systems. Waveshare Thermal-90 Camera HAT
zł347.66
4 weeks
No product available!
Gravity: High Accuracy is a multifunctional environmental sensor with Gravity I2C and UART output. Perfect for weather station projects. DFRobot SEN0501
zł136.06
24h
Available quantity: 1
Available
Module with NXP temperature sensor. It allows you to measure temperature in the range from -55 °C to +125 °C. I2C interface. The board is equipped with a Pmod I2C standard connector and a KAMAMI connector