SparkFun Digital Temperature Sensor Breakout - TMP102
ID: 564322
5906623417858
zł29.82
Tax included
zł24.24 tax excl.
SEN-13314
Description:
The TMP102 is an easy-to-use digital temperature sensor from Texas Instruments. The TMP102 breakout allows you to easily incorporate the digital temperature sensor into your project. While some temperature sensors use an analog voltage to represent the temperature, the TMP102 uses the I2C bus of the Arduino to communicate the temperature. Needless to say, this is a very handy sensor that doesn’t require much setup.
The TMP102 is capable of reading temperatures to a resolution of 0.0625°C, and is accurate up to 0.5°C. The breakout has built-in 4.7kΩ pull-up resistors for I2C communications and runs from 1.4V to 3.6V. I2C communication uses an open drain signaling, so there is no need to use level shifting.
Features:
- Uses the I2C interface
- 12-bit, 0.0625°C resolution
- Typical temperature accuracy of ±0.5°C
- 3.3V sensor
- Supports up to four TMP102 sensors on the I2C bus at a time
564322
Data sheet
- Interface
- I2C
- Type of sensor
- TMP102
- Power supply voltage
- 1,4 - 3,6 V
- Sensor type
- Temperatury
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Available
LM35 analog temperature sensor module. It allows you to measure the temperature in the range from 0°C to 100°C with a resolution of 0.5°C
zł18.55
24h
Available quantity: 7
Available
Other products in the same category (16)
Module with digital temperature sensor AS6212. It enables measurement in the range from –40°C to 125°C with an accuracy of 0.2°C. SparkFun SEN-18521
zł48.41
24h
Available quantity: 3
Available
Module with BME280 environmental sensor. It allows you to measure temperature, humidity and pressure. The sensor is equipped with two communication interfaces: SPI and I2C. SparkFun SEN-13905
zł112.74
24h
Available quantity: 2
Available
Non-contact temperature sensor with a measuring range from -70 to 380°C. It uses infrared waves and has a current output. DFRobot SEN0264
zł401.02
24h
Available quantity: 1
Available
A module with a temperature and humidity sensor based on the AHT20 system. It communicates via the I2C interface. DFRobot SEN0527
zł24.92
4 weeks
No product available!
IR Thermometer Evaluation Board - evaluation board with ATmega328 microcontroller and IR thermometer
Evaluation board with an IR thermometer MLX90614. The sensor is connected to the ATmega328 microcontroller working at a voltage of 3.3 V with the Arduino bootloader loaded. SparkFun SEN-10740
zł198.14
3 weeks
No product available!
The module with the MAX31850K amplifier is designed to work with a thermocouple. The board is equipped with a Grove connector and communicates via 1-Wire. Seeed Studio 101020555
zł82.45
24h
Available quantity: 2
Available
Panel thermometer with a 7-segment LED display with a measuring range from -50 to 110 °C. It is powered with the voltage of 12 V
zł12.46
24h
Available quantity: 50
Available
Temperature sensor based on the DS18B20 chip. It is enclosed in a waterproof measuring probe. It has a 2 m cable and communicates via a 1-Wire interface
zł15.95
24h
Available quantity: 26
Available
LM35 analog temperature sensor module for Arduino. DFRobot DFR0023
zł17.93
4 weeks
No product available!
Adafruit Universal Thermocouple Amplifier MAX31856 is an amplifier module for thermocouples. It was based on the MAX31856 chip. The module is fitted with K, J, N, R, S, T, E or B thermocouples. The SPI interface is used for communication. Adafruit 3263
zł88.90
4 weeks
No product available!
The module with the MCP9600 amplifier is designed to work with a thermocouple. The board is equipped with a Grove connector and communicates via I2C. Seeed Studio 101020594
zł80.27
24h
Available quantity: 1
Available
Module with 3-axis accelerometer ADXL343 and precise temperature sensor ADT7410 dedicated to Feather series boards. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4147
zł62.29
24h
Available quantity: 2
Available
Module with temperature and humidity sensor DHT11. It uses a 1-wire communication interface and has a humidity measurement range from 20 to 90% with an accuracy of 5% and temperature from 0 to 50 ºC with an accuracy of 2 ºC
zł17.05
24h
Available quantity: 5
Available
Board with a temperature sensor DS18B20 designed for modules ESP8266, ESP-01 and ESP-01S
zł9.00
24h
Available quantity: 9
Available
Temperature sensor in the form of a HT-NTC100K thermistor on a 1 m cable. Designed for 3D printers
zł5.40
24h
Available quantity: 44
Available
Module with a thermal imaging camera with an 80x42 field matrix and a 45° viewing angle. It is dedicated to work with the Raspberry Pi minicomputer and communicates via the SPI interface. Waveshare Thermal USB Camera
zł357.75
24h
Available quantity: 1
Available
SEN-13314