List of products by brand Pimoroni

Ethernet network module with W5100S chip dedicated to Raspberry Pi Pico. It communicates via the SPI interface and works with 3.3 V and 5 V systems. Pimoroni WIZnet-Ethernet-HAT

Board with RP2040 microcontroller and W5100S network chip. The module is equipped with an Ethernet connector. Pimoroni W5100S-EVB-Pico

Evaluation board with a Raspberry Pi RP2040 microcontroller and a TCP/IP W5500 controller. Pimoroni W5500-EVB-PICO

The module with the DRV8830 DC motor controller with a maximum current of 1 A. The board is equipped with a screw connector and communicates via the I2C interface. Pimoroni PIM479

Module with 6-axis IMU motion sensor that combines a 3-axis accelerometer and a 3-axis magnetometer in one system. It communicates via the I2C bus. Pimoroni PIM376

Mini water pump designed for home automatic irrigation systems. It can be submerged in water. The pump is supplied with the voltage of 4.5 V and has a power of about 0.91 W. Pimoroni COM3700

Mini board with RP2040 microcontroller equipped with two ARM Cortex-M0+ 133 MHz cores, 264 kB RAM. The board also has 8 MB of QSPI flash memory. The circuit can be programmed in C/C++, CircuitPython or MicroPython. PIM577

A module with 5 buttons and an RGB diode, designed to work with the Raspberry Pi. The buttons are connected to the minicomputer through the GPIO expander controlled by the I2C interface. Pimoroni PIM301

Module with 5x5 RGB LED matrix display (25 LEDs). It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM435

A pin expander designed for Raspberry Pi Pico boards. It is equipped with a standard female connector and two sets of male strips 2x20 pins. Pimoroni PIM556

Module with pressure and temperature sensor BMP280. It allows to read the atmospheric pressure in the range from 300 to 1100 hPa and communicates via the I2C interface. Pimoroni PIM411

Mini pin expander designed for Raspberry Pi boards. It is equipped with a standard 40-pin connector for connecting a minicomputer and a set of 2x20-pin outputs for connecting expansion modules. Pimoroni PIM300

Mini board with the RP2040 microcontroller equipped with two ARM Cortex-M0 + cores, which work at a frequency of 133 MHz and 264 kB RAM. The board also has 8 MB of QSPI flash memory. The system can be programmed in C/C++ or MicroPython. Pimoroni PIM558

Power management module designed for the Raspberry Pi. Equipped with a microUSB connector and a minicomputer power supply button. Pimoroni PIM269

Module with a potentiometer and RGB backlight. It has a limited range of motion and is perfect for e.g. lighting control. Pimoroni PIM523

A power supply module with a LiPo and Li-Ion battery charger dedicated to the Raspberry Pi Pico boards. It has a built-in button and over-discharge and overload protection. Pimoroni PIM557

Module with 17x7 LED matrix display (119 LEDs) designed to work with the Raspberry Pi. It uses the IS31FL3731 driver and communicates via the I2C interface. Pimoroni PIM491

Module with a 3-axis motion sensor MSA301 (accelerometer), which allows to measure acceleration in the range of ±2/±4/±8/±16 g. Communicates via the I2C bus. Pimoroni PIM456

Module with encoder and RGB backlight. It has an unlimited range of motion and is perfect for e.g. lighting control. Pimoroni PIM522

A female-female cable, 50 mm long, terminated on both sides with a JST-ZH 2-pin plug. Suitable for micro DC motor modules. Pimoroni CAB1012