Category: Gravity peripheral modules (DFRobot)
There are 247 products.
Audio module with 8 Ohm loudspeaker and 8002B amplifier. It can be used as a buzzer and also play high-quality sound. The volume is controlled by a potentiometer. DFRobot FIT0449
Module with MOSFET transistor, 5-36 V, 20 A, switching frequency 1 kHz. DFRobot DFR0457
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 10 A. DFRobot SEN0288
DFR0464
Gravity: I2C ADS1115 The 16-Bit ADC Module is an analogue-to-digital converter module for Arduino and Raspberry Pi. This module uses 16-bit ADC ADS1115 and is powered by 3.3 ... 5V. DFRobot DFR0553
Gravity: UART MP3 Voice Module is an MP3 sound player module with a built-in 8 MB memory. It is powered by 3.3-5V and controlled by the UART interface. DFRobot DFR0534
Gravity module with a colored RGB WS2812 LED. Thanks to the controller built into the diode, you can connect the modules in series and control all with one microcontroller port. DFRobot DFR0605
Switch module with an interlock. DFRobot DFR0423
A module with a 16-channel input/output port expander controlled by an I2C interface. It was based on the MCP23017 chip and equipped with a Gravity connector. DFRobot DFR0626
Module with MLX90614-DCC sensor for non-contact temperature measurement in the range from -70℃ to 380℃. I2C communication. DFRobot SEN0206
Gravity: I2C 12-Bit DAC is a module with 12-bit DAC and built-in EEPROM memory. The module is powered by 3.3 ... 5V for communication used by the I2C interface. DFRobot DFR0552
An expansion board designed for FireBeetle M0 and ESP32-E kits. The board has 12 GPIO pins, 5 ADC, UART, I2C and SPI interfaces. The pins are color coded according to the Gravity standard. DFRobot DFR0762
A set of 10 cables, 30 cm long, compliant with the Gravity standard. DFRobot FIT0513
Gravity: Digital Capacitive Touch Sensor is a capacitive touch sensor powered by 3.3V ... 5V voltage. DFRobot DFR0030
Starter kit with Arduino. The kit includes the DFRduino Uno R3 board and 12 of the most popular components and sensors. The set includes an illustrated manual with sample projects. DFRobot KIT0111
This sensor utilizes advanced signal processing technology by using a powerful chip (XKC-Y25-T12V) with high-speed operation capacity to achieve non-contact liquid level detection; suitable for hazardous applications: detecting toxic substances and all kinds of liquid in an airtight container under high pressure. SEN0204
8-port I2C splitter module. The board is equipped with a Gravity connector and allows you to connect additional I2C devices. DFRobot DFR0759
Water pressure sensor with 3-pin Gravity interface. It enables the measurement of liquid pressure in the range from 0 to 1.6 MPa. It is supplied with the voltage of 5 V and has a linear output voltage from 0.5 to 4.5 V. DFRobot SEN0257
Set with the ADC HX711 transducer module and a pressure sensor in the form of a tensometric beam. It communicates via the UART interface. It allows you to build a simple home scale. DFRobot SEN0160
Gravity: DS18B20 Temperature Sensor is a module with a temperature sensor compatible with Arduino boards. The module can be supplied with 3.3-5V voltage and measures the temperature in the range -55 ~ 125 ° C. DFRobot DFR0024