Gravity: Digital Push Button - button with LED (red)
ID: 581617
5906623406449
zł7.52
Tax included
zł6.11 tax excl.
Module with a button, LED diode and a red cap. DFRobot DFR0029-R
Description
Module with a monostable button and a LED indicating its status. A red cap has been attached to the button, which increases the convenience of using the button. The Wiki page contains the manual and sample programs.
Features
- Digital output
- Easy to assemble and connect
- Signal diode
- Red cap
- Gravity connector
- Supply voltage: from 3.3 V to 5 V
- Size: 22 x 30 mm
Kit contains
- Module with a button
- Gravity cable
581617
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Arduino Uno Rev3 is a popular board with Atmel ATmega328 microcontroller from the AVR family, there are 14 I / O lines, 6 PWM channels and 6 analog inputs. The additional ATmega16U4 microcontroller realizes communication via the USB interface. Arduino A000066
zł108.42
24h
Available quantity: 105
Available
Available
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł22.82
24h
Available quantity: 1
Available
Module with a button, LED diode and a blue cap. DFRobot DFR0029-B
zł11.30
24h
Available quantity: 3
Available
Module with a button, LED diode and a yellow cap. DFRobot DFR0029-Y
zł8.38
24h
Available quantity: 1
Available
Module with a button, LED diode and a white cap. DFRobot DFR0029-W
zł7.82
24h
Available quantity: 3
Available
Module with a button, LED diode and a green cap. DFRobot DFR0029-G
zł11.29
24h
Available quantity: 1
Available
Other products in the same category (16)
Module with a button and green LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-G
zł19.93
24h
Available quantity: 3
Available
Waveshare 8 Push Buttons module provides 8 single push buttons in 1 board. Waveshare 3678
zł7.13
24h
Available quantity: 7
Available
KAmodPCF8883T is a module with capacitive touch sensor PCF8883 from NXP. The module has a probe placed on the PCB and a diode indicating the state of the chip. It enables work in one of three modes.
zł19.90
24h
Available quantity: 441
Available
Module for 4 mechanical buttons with LED backlight in the form of NeoPixel diodes. Communicates via I2C. Adafruit 4980
zł53.41
24h
Available quantity: 2
Available
Available
Module with a button, LED diode and a white cap. DFRobot DFR0029-W
zł7.82
24h
Available quantity: 3
Available
Module with a button and blue LED backlight. The board is equipped with a Gravity connector and communicates via a digital interface. DFRobot DFR0785-B
zł19.91
24h
Available quantity: 3
Available
Module with 5 colored buttons. Each button is powered independently and has an output informing about its status
zł8.54
24h
Available quantity: 9
Available
Membrane keypad module with 4 buttons. It is equipped with a tape terminated with a 5-pin connector
zł4.69
24h
Available quantity: 22
Available
Module with backlight in the form of RGB NeoPixel diode dedicated to CHOC buttons (or compatible). Adafruit 5756
zł9.90
4 weeks
No product available!
Module with a button and yellow LED backlight. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020045
zł12.46
24h
Available quantity: 1
Available
Touch keyboard module with 4 buttons based on the TTP224 system. It is equipped with a connector with derived signals and 4 LEDs signaling the state of each button
zł5.81
24h
Available quantity: 1
Available
Two-button module with 4 colored overlays. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020103
zł17.00
4 weeks
No product available!
Module with a button and blue LED backlight. The board is equipped with a Grove connector and communicates via a digital interface. Seeed Studio 111020046
zł12.47
24h
Available quantity: 1
Available
Module with a button and green LED backlight. Controlled by the I2C interface, it has a built-in debouncing mechanism, pull-up resistors as well as interrupts and a FIFO queue. SparkFun BOB-16842
zł27.76
24h
Available quantity: 1
Available
Module with a button and a cover in red
zł1.94
24h
Available quantity: 56
Available
Module with a button, LED diode and a red cap. DFRobot DFR0029-R