Category: Expanders of the I/O
There are 64 products.
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.
Module with a TL281 4-channel optocoupler with a maximum collector-emitter voltage of 80 V
Module with 16-channel I/O ports expander controlled by the I2C interface. It was based on the MCP23017 chip
16-channel I/O port expander module controlled by the I2C interface. The module is based on the MCP23017-E/SS system.
Measurement module with RS485 interface. It has two voltage measurement inputs in the range of 0 to 5 V and 0 to 10 V and two current measurement inputs in the range of 0 to 20 mA. Supports the Modbus RTU protocol
16-channel GPIO expander with an I2C interface microcontroller can interface with 16 fully configurable digital input/output pins. It can produce PWM signals, so you can dim LEDs. It can be set to blink or even breathe pins at varying rates. With a built-in keypad engine, it can interface with up to 64 buttons set up in an 8x8 matrix. BOB-13601
A 4-channel I2C expander module, which is based on the TCA9546A chip. It allows connecting several devices with the same address to a single I2C interface. Adafruit 5663
A 24-channel input/output port expander module controlled by an I2C interface. It was based on the CH423 chip and equipped with a Gravity connector. DFRobot DFR0979
Module with 8 digital inputs and 8 digital outputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8028ADAM
Module with 8 inputs for data acquisition from DS18B20 temperature sensors. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP3066ADAM
Module with 4 digital inputs, 4 outputs and 6 analog inputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP9039ADAM
I2C multiplexer module with TCA9548A system. Allows you to connect up to 8 devices. The system works like a gateway - it transmits I2C interface data to one of the 8 main busses. This allows you to connect up to 8 devices with the same address. Adafruit 2717
Module with 8-channel PCF8574 IO expander controlled by the I2C interface. Equipped with a STEMMA QT connector. Adafruit 5545
Module with 8 digital inputs and 4 relays with a maximum switching current of 2 A. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8024ADAM
Module with 16 digital outputs. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP8027ADAM
Module with 8 analog inputs for current measurement in the range of 0 to 20 mA or 4 to 20 mA. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP3082ADAM
Module with 16-channel PCF8575 IO expander controlled by the I2C interface. Equipped with a STEMMA QT connector. Adafruit 5611
8-channel I2C expander module based on the PCA9548 chip. Allows communication with multiple I2C devices that have the same address. Equipped with STEMMA QT connectors. Adafruit 5626
I2C bus amplifier module based on the LTC4311 system. It enables communication via a popular interface over much longer distances while maintaining high transmission speeds. Adafruit 4756
Module with 8 analog inputs for voltage measurement in the range from 0 to 10 V. It communicates via the RS485 interface and supports the Modbus RTU protocol. The board is enclosed in an industrial housing. Wellpro WP3084ADAM