- -zł27.71
16-channel I/O port expander module controlled by the I2C interface. The module is based on the Microchip MCP23017-E/SS system. Each IO pin can be configured as input or output, a pull-up resistor and an interrupt function can be set for the IO configured as input. The maximum output current should not exceed 25 mA. Interjest I2C can operate at 100KHz, 400KHz and 1.7MHz. The module has 3 address jumpers that can be configured as 8 different addresses, so the modules can be connected to one I2C interface.
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Pin header goldpin black 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
Pin header goldpin black 1x40 pins. Angled connector for through-hole assembly. 2.54mm pitch.
Pin header goldpin red 1x40 studs. Straight connector for through-hole assembly. 2.54mm pitch.
Pin header goldpin yellow 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
Pin header goldpin blue 1x40 pins. Straight connector for through-hole assembly. 2.54mm pitch.
IO port expander for M5Stack kits. Equipped with 8 IO pins and power pins, it communicates via the I2C interface. M5Stack U011-B
Module with IO expander equipped with 14 inputs/outputs, including 8 connected to the ADC converter and 6 to PWM outputs. It communicates via the I2C interface and is compatible with the Raspberry Pi. Pimoroni PIM517
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.
Module with a 16-channel GPIO expander with the ability to control LEDs. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4886
I2C bus amplifier module based on the LTC4311 system. It enables communication via a popular interface over much longer distances while maintaining high transmission speeds. Adafruit 4756
No product available!
Adapter dedicated to the Nintendo Wii Nunchuck. It allows you to connect the controller to the development board via the I2C interface. Adafruit 4836
Module with 16-channel I/O ports expander controlled by the I2C interface. It was based on the MCP23017 chip
Module with 16-channel IO expander MCP23017 controlled by the I2C interface. Equipped with a STEMMA QT connector. Adafruit 5346
No product available!
4-channel PCIe port expander. It can be powered with 12 V via a PCIe connector or an external DC connector. Waveshare PCIe-Packet-Switch-4P
Module with a 16-channel GPIO expander with the ability to control LEDs. It communicates via the I2C interface. Waveshare AW9523B IO Expansion Board
No product available!
128-channel IO expander with 32 analog inputs. It communicates via the USB interface. Numato Lab GP1280001
No product available!
16-channel IO expander with 10 analog inputs. The board communicates via the Ethernet interface. Numato Lab GPETH160001
No product available!
16-channel IO expander with 7 analog inputs. It communicates via the USB interface. Numato Lab GP160001
16-channel IO expander with 14 analog inputs. Communicates via the WiFi wireless interface. Numato Lab GPWIFI160001
No product available!
32-channel IO expander with 14 analog inputs. The board communicates via the Ethernet interface. Numato Lab GPETH320001
32-channel IO expander with 7 analog inputs. It communicates via the USB interface. Numato Lab GP320001
No product available!
16-channel I/O port expander module controlled by the I2C interface. The module is based on the MCP23017-E/SS system.