New products
New products
Category: STM32
Subcategories
There are 95 products.
10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini
Single board computer with STM32F207VE microcontroller (ARM Cortex-M3, 512 kB Flash, 128 kB RAM, LQFP100).
Low cost programmer for STM32 and STM8 microcontrollers fully compatible
with the ST-Link V2
A new programmer-debugger with the USB interface. It supports the STM32 microcontrollers via SWD interface. ZL30PRGv2-1 is compatible with the STMicroelectronics ST-Link/V2-1. It also has the function of USB-UART converter, thanks to which it can successfully replace the KAmodRS module.
Debugger/programmer with a USB interface that supports the SWD (Serial Wire Debbug) programming interface. It is based on CMSIS-DAP (Coresight Debug Access Port) and also has a USB-UART converter function
Evaluation kit equipped with STM32F401CCU6 microcontroller (ARM Cortex M4, 84MHz, 256kB Flash, 64kB RAM). It has two 20-pin connectors enabling the use of numerous microcontroller peripheral systems.
Development kit with STM32L496ZGT6 microcontroller with built-in ST-Link programmer. Extensive equipment, including: MEMS 6DoF sensor, motor controller, joystick, LED display, 8 LED diodes, RGB LED, audio amplifier, Flash memory QSPI 1 MB, microphone.
Universal minicomputer with STM32F103C6 microcontroller (ARM Cortex-M3 @72 MHz, 32 kB Flash, 10 kB RAM, LQFP48 package)
Evaluation kit equipped with equivalent of STM32F103C8T6 microcontroller (ARM Cortex M3, 72MHz, 64kB Flash, 20kB SRAM). It has two 20-pin connectors enabling the use of numerous microcontroller peripheral systems
Compact tool for debugging and programming STM32 microcontrollers via JTAG / SWD interfaces. STMicroelectronics STLINK-V3MINIE
Development kit with STM32L496ZGT6 microcontroller (ARM Cortex-M4 core) with a built-in ST-Link programmer. Extensive equipment, including: MEMS 6DoF sensor, motor controller, joystick, LED display, 8 LED diodes, RGB LED, audio amplifier, Flash memory QSPI 1 MB, microphone, Arduino connector
The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and a complementary adapter board
Compact programmer module for STM32 microcontrollers for soldering into a board. Supports JTAG/SWD interfaces. STLINK-V3SET has a virtual COM port and interfaces SPI, I2C, CAN, GPIO for programming via bootloader. STMicroelectronics STLINK-V3MODS
ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 microcontrollers
JTAG interface for microcontrollers with ARM core
The STM32F7 discovery kit allows users to develop and share applications with the STM32F7 Series microcontrollers based on the ARM®Cortex®-M7 core.
KA-NUCLEO-F411CE v2 is a development board based on the STM32F411CE microcontroller. It has a built-in programmer compatible with ST-Link / v2-1, it is possible to program and debug the microcontroller via the USB connector.
Evaluation kit equipped with STM32F411CEU6 microcontroller (ARM Cortex M4, 100MHz, 512kB Flash, 128kB RAM). It has two 20-pin connectors enabling the use of numerous microcontroller peripheral systems.
J-LINK EDU Mini is a version of the J-Link EDU (8.08.90) in a reduced form factor with identical functionality for Cortex-M based targets. It has been designed to allow students and educational facilities as well as hobbyists access to top of the line debug probe technology. Version for non-commercial use only. J-Link EDU mini
Universal board for ZL40ARM and ZL41ARM kits