10-wire ribbon cable for Segger J-Link EDU mini
ID: 565483
zł34.42
Tax included
zł27.98 tax excl.
10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini
Description
This cable allows to connect J-Link EDU mini (JTAG connector pitch: 1.27mm) to every Development Board with IDC20 connector 2.54mm pitch.
Features
- 10-wire ribbon cable, 2x5 pin, 50 mil to IDC20 2.54 mm pitch
- Lenght: 19cm
- Compatible with programmer J-Link EDU mini
565483
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
J-LINK EDU Mini is a version of the J-Link EDU (8.08.90) in a reduced form factor with identical functionality for Cortex-M based targets. It has been designed to allow students and educational facilities as well as hobbyists access to top of the line debug probe technology. Version for non-commercial use only. J-Link EDU mini
zł264.68
Delivery date unknown
No product available!
Other products in the same category (16)
J-Link Needle Adapter - connect J-Link to a PCB, Segger
zł521.14
24h
Available quantity: 5
Available
10-pin Needle Adapter to connect Flasher 5, Flasher ST7 or Flasher STM8 to a PCB, Segger
zł521.14
1 weeks
No product available!
Standard 20-pin 0.1 male connector to provide electrical isolation, Segger
zł1,023.73
24h
Available quantity: 4
Available
J-Link ARM-14 Adapter, RoHS
zł354.39
24h
Available quantity: 1
Available
J-Link 19-pin Cortex-M Adapter, RoHS, Segger
zł164.33
24h
Available quantity: 3
Available
J-Link 9-pin Cortex-M Adapter, RoHS, Segger
zł166.12
24h
Available quantity: 2
Available
No product available!
J-Link 14-pin TI Adapter, RoHS, Segger
zł255.37
24h
Available quantity: 1
Available
No product available!
The Segger J-Link Signal Smoothing Adapter (8/06/12) is designed to improve signal integrity between the J-Link debug probe and the target debug device. It allows JTAG signals to be suppressed by adjustable series resistors, preventing excessive gain and jitter.
zł260.56
1 weeks
No product available!
The Segger J-Link Measurement+Patch Adapter allows you to easily customize connections between J-Link or Flasher devices and boards that do not have a standard debug connector. It is equipped with colored wires for signal identification, test points and jumpers for adjusting the voltages on the pins.
zł521.14
1 weeks
No product available!
The Segger J-Link Supply Adapter (8.06.14) allows you to manually set the debug probe I/O voltage, preventing damage to the target board, adjustable from 1.2V to 5.0V. It can be inserted between J-Link or Flasher and the target device, reducing the number of connections needed, which is especially useful in a production environment.
zł349.78
24h
Available quantity: 1
Available
The Intel FPGA Adapter (formerly J-Link Altera Adapter) connects to the Intel FPGA 10-pin JTAG connector, enabling debugging of FPGA-based MCU cores such as the dual-core Arm Cortex-A9 in Cyclone V devices. on Intel FPGA solutions.
zł254.71
1 weeks
No product available!
J-Link 6-pin Needle Adapter (8.06.16)
zł544.74
24h
Available quantity: 5
Available
The Segger J-Link Mictor 38 Adapter allows connection to a 38-pin Mictor connector in accordance with the ARM "ETM" specification. The adapter connects the GND and JTAG pins to the 20-pin J-Link, and the trace pins on the Mictor connector are not used.
zł787.02
1 weeks
No product available!
10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini
zł34.42
24h
Available quantity: 217
Available
10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini