Segger USB Hub (5/01/10)

J-Link 14-pin TI Adapter, RoHS, Segger

J-Link TI-CTI-20 Adapter, RoHS, Segger

J-Link RX Adapter, RoHS, Segger

The Segger J-Link Microchip Adapter (8/06/09) provides a debug connection between a J-Link probe and hardware with Microchip PIC32 series microcontrollers. Supports RJ12 debug connector, 14-pin MIPS connector and 6-pin PICkit connector.

A 1:1 adapter that allows you to connect a standard 20-pin connector to its 2mm pitch counterpart without any additional configuration. For some models, such as the J-Link PRO, pins 14, 16, 18 and 20 may not be connected to ground, so it is recommended to leave them unconnected on the target hardware. Segger 2mm Adapter (06/08/11)

Xilinx adapter that connects to Xilinx\'s 14-pin, 2mm JTAG connector, providing debugging of MCU cores such as the Arm Cortex-A9 on Xilinx Zynq FPGAs. With its compact design and high signal quality, it is a reliable tool for engineers working with FPGA platforms. Segger Xilinx Adapter (06/08/19)

Power adapter providing a stabilized 5V supply voltage for the target board. Segger 5V Target Supply Adapter (8.06.29)

The RX FINE adapter converts a standard 20-pin 2.54 mm connector to a 14-pin 2.54 mm connector. It enables the connection of Segger programmers with RX devices from Renesas. Segger RX Fine Adapter (8.06.10)

The adapter is designed to support a wide range of RL78 microprocessor cores manufactured by Renesas, such as the RL78/D1A, RL78/F12, RL78/F13, RL78/F14, RL78/F15, and the RL78/G and RL78/I series. The adapter enables quick and easy connection to target devices, providing full flash programming functionality, making it a versatile tool for industrial and embedded applications. Segger RL78 Adapter (06/08/20)

Standard 20-pin 0.1 male connector to provide electrical isolation, Segger

Adapter that converts standard 20-pin 2.54 mm connector to SWIM connector and 10-pin connector. Used for programming STM8 chips. Segger STM8 Adapter (8.06.22)

Adapter that enables JTAG connection between Flasher programmer and target hardware with Power Architecture or PowerPC microcontrollers. Converts 20-pin 0.1\'\' connector to 14-pin JTAG, ensuring compatibility, stability and secure connection. Segger PPC 14-Pin Adapter (06.08.07)

The Segger J-Link Mictor 38 Adapter allows connection to a 38-pin Mictor connector in accordance with the ARM "ETM" specification. The adapter connects the GND and JTAG pins to the 20-pin J-Link, and the trace pins on the Mictor connector are not used.

The Segger J-Link Supply Adapter (8.06.14) allows you to manually set the debug probe I/O voltage, preventing damage to the target board, adjustable from 1.2V to 5.0V. It can be inserted between J-Link or Flasher and the target device, reducing the number of connections needed, which is especially useful in a production environment.

The Segger J-Link USB Isolator (8.07.02) provides isolation up to 3 kV DC and supports USB Full-Speed transmission with a maximum output current of 200 mA. The device is equipped with short-circuit protection and LED indicators for power status and overload.

An adapter that converts a standard 20-pin 2.54 mm connector to a 10-pin 2.54 mm connector. It enables the connection of Segger programmers with Silicon Labs devices and development boards with a C2 interface. Segger SiLabs C2 Adapter (8.06.17)