RL78 Adapter (8.06.20)

A 1:1 adapter that allows you to connect a standard 20-pin connector to its 2mm pitch counterpart without any additional configuration. For some models, such as the J-Link PRO, pins 14, 16, 18 and 20 may not be connected to ground, so it is recommended to leave them unconnected on the target hardware. Segger 2mm Adapter (06/08/11)

Segger adapter 8.06.28 allows conversion from a 20-pin 0.1" connector to a 10-pin 0.05" Cortex-M type connector with the option of custom pin mapping. A useful solution for integrating programmers and debuggers with devices featuring different pin configurations.

Adapter enabling connection of OCDS DAP interface to systems based on Infineon Aurix™ TC2xx, TC3xx, TC4xx and C167 microcontrollers. Converts standard 20-pin SEGGER connector to 10-pin 0.05\'\' Samtec FTSH, providing stable and reliable communication in debugging and programming processes. Segger Infineon Aurix DAP-10 Adapter (8.06.38)

Adapter providing two dedicated supply voltages - for programming and powering for the target board. Useful for programming modules that do not support low voltage programming or require a voltage other than 5V. Segger Programming Voltage Adapter (8.06.30)

AVR PDI adapter from standard 2.54mm 20 pin connector to 2.54mm 6 pin, 1.27mm 6 pin or 2.54mm 10 pin AVR PDI connector. Segger AVR PDI Adapter (8.06.26)

The Segger J-Link Measurement+Patch Adapter allows you to easily customize connections between J-Link or Flasher devices and boards that do not have a standard debug connector. It is equipped with colored wires for signal identification, test points and jumpers for adjusting the voltages on the pins.

An adapter that allows the J-Link device to connect to Microchip microprocessors that use an RJ11 debug connector, converting the standard 20-pin .1" connector to a 6-pin RJ11 connector. With this tool, users can take full advantage of 2-wire JTAG debugging capabilities, including process tracing, memory analysis, and real-time device control, and the 21 cm RJ11 cable provides convenience in connecting to the target system. Segger Microchip 2-Wire JTAG TDI Adapter (06/08/23)

The Segger J-Link USB Isolator (8.07.02) provides isolation up to 3 kV DC and supports USB Full-Speed transmission with a maximum output current of 200 mA. The device is equipped with short-circuit protection and LED indicators for power status and overload.

RS232 module used as a communication extension equipped with a female DSUB9 connector, allowing easy connection to a PC or USB-RS232 adapter. Segger emPower RS232 Add-On (6.32.32)

An adapter that converts a standard 20-pin 2.54 mm connector to a 10-pin 2.54 mm connector. It enables the connection of Segger programmers with Silicon Labs devices and development boards with a C2 interface. Segger SiLabs C2 Adapter (8.06.17)

A module that enables precise switching of Flasher signals in production environments, preventing interference between test devices connected to the same lines. By controlling relays via VTSUPPLY, it ensures stable and reliable operation in testing and programming processes. Segger Relay Adapter (8.06.41)

The RX FINE adapter converts a standard 20-pin 2.54 mm connector to a 14-pin 2.54 mm connector. It enables the connection of Segger programmers with RX devices from Renesas. Segger RX Fine Adapter (8.06.10)

Compact evaluation board for testing NOR and NAND flash memory supported by emFile drivers. Enables fast and reliable flash programming with SEGGER tools, offering support for various packages such as SO-8, SO-16, BGA and SON. SEGGER (Q)SPI Flash Evaluator (6.40.00)

J-Link SDK one year Support and Update Agreement extension. Can only be purchased by customers with a J-Link SDK License (Model 8.08.06). Segger J-Link SDK Extension (8.08.18)

SiFive-ARTY adapter for debugging between J-Link and the ARTY board with SiFive RISC-V. Segger SiFive-ARTY Adapter (8.06.24)

A compact adapter that provides direct pin compatibility, allowing easy replacement of standard IDC cable without changing the pinout. It is designed to work with devices such as the J-Link PLUS Compact, J-Link BASE Compact and Flasher Compact, enabling flexible and efficient debugging and programming configurations in embedded systems. Segger Right Angle (RAFF) Adapter (8.06.32)