Segger Programming Voltage Adapter (8.06.30) - Segger power adapter
ID: 586717
zł521.14
Tax included
zł423.69 tax excl.
Adapter providing two dedicated supply voltages - for programming and powering for the target board. Useful for programming modules that do not support low voltage programming or require a voltage other than 5V. Segger Programming Voltage Adapter (8.06.30)
Description
Adapter providing two dedicated supply voltages - for programming and powering for the target board. Both voltages are supplied by an external power source to the connector on the adapter and are controlled by the SEGGER Flasher. This adapter is especially useful for programming modules that do not support low voltage programming or require a voltage other than 5V. If the target device requires 5V power, the jumper on the adapter can be switched to use 5V from the Flasher so only one external power supply (providing programming voltage). Both channels accept a voltage in the range from 4 to 20 V and can operate with a maximum current of 500 mA.
It has a standard 20-pin 2.54mm socket for connecting a J-Link or Flasher programmer and a 20-pin 2.54mm socket on the device side. The adapter can be directly clipped between the J-Link or Flasher and the debugging cable.
586717
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
Hi-Speed JTAG/SWD Emulator with USB and Ethernet interface, Segger
zł5,235.58
Delivery date unknown
No product available!
JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
zł3,139.86
24h
Available quantity: 7
Available
Available
Flash Programmer for ARM7/9/11, Cortex, RX and PPC cores
zł5,161.83
24h
Available quantity: 1
Available
Portable Flash programmer for built-in and external flash memory. Segger Flasher Portable PLUS
zł5,211.50
24h
Available quantity: 1
Available
Flash programmer for programming microcontrollers and external (Q) SPI memories. Segger Flasher Compact
zł4,775.25
Delivery date unknown
No product available!
Other products in the same category (16)
Standard 20-pin 0.1 male connector to provide electrical isolation, Segger
zł1,023.73
24h
Available quantity: 4
Available
J-Link ARM-14 Adapter, RoHS
zł354.39
24h
Available quantity: 1
Available
J-Link 19-pin Cortex-M Adapter, RoHS, Segger
zł164.33
24h
Available quantity: 3
Available
J-Link 9-pin Cortex-M Adapter, RoHS, Segger
zł166.12
24h
Available quantity: 2
Available
No product available!
J-Link 14-pin TI Adapter, RoHS, Segger
zł255.37
24h
Available quantity: 1
Available
No product available!
The Segger J-Link Signal Smoothing Adapter (8/06/12) is designed to improve signal integrity between the J-Link debug probe and the target debug device. It allows JTAG signals to be suppressed by adjustable series resistors, preventing excessive gain and jitter.
zł260.56
1 weeks
No product available!
The Segger J-Link Measurement+Patch Adapter allows you to easily customize connections between J-Link or Flasher devices and boards that do not have a standard debug connector. It is equipped with colored wires for signal identification, test points and jumpers for adjusting the voltages on the pins.
zł521.14
1 weeks
No product available!
The Segger J-Link Supply Adapter (8.06.14) allows you to manually set the debug probe I/O voltage, preventing damage to the target board, adjustable from 1.2V to 5.0V. It can be inserted between J-Link or Flasher and the target device, reducing the number of connections needed, which is especially useful in a production environment.
zł349.78
24h
Available quantity: 1
Available
The Intel FPGA Adapter (formerly J-Link Altera Adapter) connects to the Intel FPGA 10-pin JTAG connector, enabling debugging of FPGA-based MCU cores such as the dual-core Arm Cortex-A9 in Cyclone V devices. on Intel FPGA solutions.
zł254.71
1 weeks
No product available!
J-Link 6-pin Needle Adapter (8.06.16)
zł544.74
24h
Available quantity: 5
Available
The Segger J-Link Mictor 38 Adapter allows connection to a 38-pin Mictor connector in accordance with the ARM "ETM" specification. The adapter connects the GND and JTAG pins to the 20-pin J-Link, and the trace pins on the Mictor connector are not used.
zł787.02
1 weeks
No product available!
10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini
zł34.42
24h
Available quantity: 225
Available
An advanced tool that enables the integration of J-Link support into your own applications, used in both development environments and custom production tools. Supports debugging, flash programming, and application testing, offering support for Windows, Linux, and macOS, as well as compatibility with many programming languages via a DLL or shared library. Segger J-Link SDK (08.08.06)
zł10,528.97
1 weeks
No product available!
J-Link SDK one year Support and Update Agreement extension. Can only be purchased by customers with a J-Link SDK License (Model 8.08.06). Segger J-Link SDK Extension (8.08.18)
zł5,211.31
1 weeks
No product available!
Adapter providing two dedicated supply voltages - for programming and powering for the target board. Useful for programming modules that do not support low voltage programming or require a voltage other than 5V. Segger Programming Voltage Adapter (8.06.30)