Segger J-Link SDK Extension (8.08.18)

Compact evaluation board for testing NOR and NAND flash memory supported by emFile drivers. Enables fast and reliable flash programming with SEGGER tools, offering support for various packages such as SO-8, SO-16, BGA and SON. SEGGER (Q)SPI Flash Evaluator (6.40.00)

An adapter to connect the JTAG to a target hardware system that has an automotive connector. It has a 20 pin 2.54mm JTAG connector and a 19 pin 1.27mm Samtec FTSH connector. Segger Infineon AUTO-20 Adapter (8.06.33)

The Segger J-Link Microchip Adapter (8/06/09) provides a debug connection between a J-Link probe and hardware with Microchip PIC32 series microcontrollers. Supports RJ12 debug connector, 14-pin MIPS connector and 6-pin PICkit connector.

Adapter that enables JTAG connection between Flasher programmer and target hardware with Power Architecture or PowerPC microcontrollers. Converts 20-pin 0.1\'\' connector to 14-pin JTAG, ensuring compatibility, stability and secure connection. Segger PPC 14-Pin Adapter (06.08.07)

Advanced evaluation board designed for rapid implementation of embedded solutions. Supporting the embOS operating system and SEGGER tools such as emFile, emWin, emUSB and emNet, the board is an ideal platform for software testing and application development in an environment based on the Xilinx Zynq XC7Z007S SoC with ARM Cortex-A9 processor and Artix7 FPGA. Segger emPower Zynq (6.31.00)

SiFive-ARTY adapter for debugging between J-Link and the ARTY board with SiFive RISC-V. Segger SiFive-ARTY Adapter (8.06.24)

The Segger J-Link Supply Adapter (8.06.14) allows you to manually set the debug probe I/O voltage, preventing damage to the target board, adjustable from 1.2V to 5.0V. It can be inserted between J-Link or Flasher and the target device, reducing the number of connections needed, which is especially useful in a production environment.

J-Link TI-CTI-20 Adapter, RoHS, Segger

Standard 20-pin 0.1 male connector to provide electrical isolation, Segger

A specialized demonstration board designed to support Tail Tagging within the embOS/IP IP stack. Using this technology, it is possible to transform a single Ethernet port into several logical ports, enabling the creation of a virtual multiport network using only a single Ethernet port. Segger embOS/IP Switch Board (6.70.00)

J-Link 6-pin Needle Adapter (8.06.16)

An adapter that allows the J-Link device to connect to Microchip microprocessors that use an RJ11 debug connector, converting the standard 20-pin .1" connector to a 6-pin RJ11 connector. With this tool, users can take full advantage of 2-wire JTAG debugging capabilities, including process tracing, memory analysis, and real-time device control, and the 21 cm RJ11 cable provides convenience in connecting to the target system. Segger Microchip 2-Wire JTAG TDI Adapter (06/08/23)

J-Link 9-pin Cortex-M Adapter, RoHS, Segger

A 1:1 adapter that allows you to connect a standard 20-pin connector to its 2mm pitch counterpart without any additional configuration. For some models, such as the J-Link PRO, pins 14, 16, 18 and 20 may not be connected to ground, so it is recommended to leave them unconnected on the target hardware. Segger 2mm Adapter (06/08/11)

Professional reference board with ARM Cortex-M4F microcontroller, designed for code tracing and real-time application analysis. Equipped with an external 19-pin debug port and test points for trace signals, it enables easy integration with J-Link and J-Trace programmers, supporting Embedded Trace Macrocell (ETM) technology. Segger Cortex-M Trace Reference Board (6.68.18)

Compact development board with NXP LPC54605J512 microcontroller, ideal for prototyping and testing USB solutions, equipped with two USB-Host ports and support for SEGGER software such as emUSB-Host, emLoad and embOS. Thanks to the simple firmware update process and the built-in J-Link OB debugger, the board allows you to quickly and conveniently start working with USB devices in embedded projects. Segger emPower-USB-Host (6.90.00)