10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini

A small development kit with a SAMD21 ARM Cortex M0 + microcontroller. There are 14 GPIO connectors on the board, including 11 digital and analog pins, 10 PWM, DAC, I2C, UART, SPI, SWD. Compatible with Arduino. Seeed Studio 102010328

JTAG interface for microcontrollers with ARM core

Board with SAMD21 microcontroller with CortexM0 + core (48 MHz, 256 KB Flash, 32 KB RAM). Equipped with WiFi and BT module (based on ESP32) and IMU LSM6DS3 unit. Ideal for applications in the IoT area. Module with headers. Arduino ABX00032

Board with SAMD21 microcontroller with Cortex M0+ core (48 MHz, 256 KB Flash, 32 KB RAM). Equipped with WiFi and BT module (based on ESP32) and IMU LSM6DS3 unit. Ideal for applications in the IoT area. Arduino ABX00027

Development kit with ATSAMD21G18A microcontroller. It has 14 GPIO connectors, including 11 digital and analog pins, 10 PWM, DAC, I2C, UART, SPI, SWD. Compatible with Arduino. Seeed Studio 102010388

J-LINK EDU Mini is a version of the J-Link EDU (8.08.90) in a reduced form factor with identical functionality for Cortex-M based targets. It has been designed to allow students and educational facilities as well as hobbyists access to top of the line debug probe technology. Version for non-commercial use only. J-Link EDU mini

ATATMEL-ICE-BASIC is a programmer designed to work with AVR microcontrollers with the On-Chip Debug function and microcontrollers with the ARM Cortex-M core from Atmel. Available interfaces are JTAG, SWD, PDI, TPI, aWire, SPI and debugWire.

JTAG/SWD Emulator with USB interface

J-Link BASE is a USB powered debug probe supporting a large number of CPU cores. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs. J-link BASE Compact (8.19.00)

Hi-Speed JTAG/SWD Emulator with USB and Ethernet interface, Segger

At the Feather M0\'s heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic. 256K FLASH, 32K RAM, built in USB and battery charging. Adafruit 2772

Development kit based on ATSAMD51 with WiFi and BLE 5.0. It is equipped with a 2.4-inch LCD screen, IMU (LIS3DHTR), microphone, buzzer, microSD card slot, light sensor and infrared transmitter (IR 940nm). Seeed Studio 102991299

The board is equipped with ATSAME51 microcontroller (ARM Cortex-M core) with CAN bus and SPI Flash memory, GPIO pins and a connector for connecting the battery with the charging circuit. Adafruit 4759

JTAG/SWD debug probe with USB interface. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs. J-Link is used around the world in tens of thousand places for development and production (flash programming) purposes. J-link PLUS Compact (8.19.28)

Evaluation board with ATSAMD21 microcontroller with ARM Cortex M0 core. Equipped with motion, temperature, light, sound sensors and RGB diodes. Can be programmed in MakeCode, CircuitPython, Arduino IDE or CS Discoveries. Adafruit 3333

The board is equipped with ATSAMD51 microcontroller with ARM Cortex-M4 core and SPI Flash memory, communication interfaces and RGB diode. Adafruit 3382

The board is equipped with ATSAMD21 microcontroller with ARM Cortex-M0 core and SPI Flash memory, GPIO pins and RGB diode. Adafruit 3727

ATATMEL-ICE-PCBA is a programmer in the form of a printed circuit board (without a casing), designed to work with AVR microcontrollers with the On-Chip Debug function and microcontrollers with the ARM Cortex-M core from Atmel. Available interfaces are JTAG, SWD, PDI, TPI, aWire, SPI and debugWire.