J-Trace Isolator (8.07.10)
ID: 1189770
5902186326811
zł1,559.52
Tax included
zł1,267.90 tax excl.
A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)
Description
J-Trace Isolator is a device that provides electrical isolation between the J-Trace emulator and any ARM board using the standard 19-pin Cortex-M connector. The J-Trace Isolator ensures high-quality trace signals while protecting against electrical interference. This solution is essential when development tools are not connected to the same ground system as the application, such as in motor control systems.
The device offers 1 kV DC electrical isolation and supports a variety of applications in product development involving sensors or other analog circuits. The J-Trace Isolator protects the target equipment from electrical disturbances originating from the development computer. It is compatible with J-Trace V2 and newer versions. The device is powered by the emulator, and the power consumption from the target device is only 25 µA. It uses a standard 19-pin JTAG connector and supports frequencies up to 75 MHz for trace, 50 MHz for JTAG, and 4 MHz for SWD.
How to Use J-Trace Isolator with J-Trace PRO
- Connect the J-Trace Isolator to the J-Trace emulator.
- Turn on the J-Trace PRO.
- Make sure the green LED on the emulator side is lit. If not, follow the instructions provided.
- Connect the target device to the Isolator device side.
- If the target device is powered, the green LED on the target device side should light up.
- The red LED on the target device side lights up when the target device RESET is active (low state).
The J-Trace Isolator is designed for use with J-Trace V2 and newer versions, but can also be used with other ARM emulators with the same pinout. In such cases, ensure that 5V is supplied to pin 19 of the emulator's connector, and that the emulator is protected from damage when 5V is applied to this pin. Use of this solution is at your own risk!
Features
- ETM trace pins: Full support up to 75 MHz
- Isolation: 1 kV DC
- Voltage range: Supports voltage from 1.2 V to 5 V on the target device
- Minimum power consumption: 25 µA drawn from the target device
- JTAG 19-pin: Supports TDI, TMS, TCK, TDO, RESET, and SWD/SWO signals
- Frequencies: JTAG up to 50 MHz, SWD up to 4 MHz
- LED support: 3 LEDs indicating emulator power, target device power, and target device RESET
Kit contains
- J-Trace Isolator
- 20-pin 0.5" ribbon cable
1189770
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
J-Trace PRO for Cortex-M is setting a new standard for trace probes. It enables continuous streaming trace via its Gigabit Ethernet interface, lifting the limitations by internal buffers and slow data transmission. (j-trace-pro)
zł7,719.81
24h
Available quantity: 3
Available
An advanced device that allows you to track and analyze real-time code executed on a core with Cortex-A, Cortex-R and Cortex-M. Segger J-Trace PRO for Cortex (8.20.00)
zł10,359.66
Delivery date unknown
No product available!
An advanced device that allows real-time tracking and analysis of code executed on a RISC-V core chip. Segger J-Trace PRO for Cortex (8.20.00)
zł10,528.97
Delivery date unknown
No product available!
Advanced code analysis and embedded debugging probe featuring real-time streaming tracing, Live Code Profiling, and Live Code Coverage. Supports a wide range of architectures including Arm, RISC-V, and Renesas RX, and features USB 3.0 and Gigabit Ethernet for fast data transfer and reliable operation. Segger J-Trace PRO (8.24.00)
zł15,595.23
Delivery date unknown
No product available!
Other products in the same category (16)
10-pin Needle Adapter to connect Flasher 5, Flasher ST7 or Flasher STM8 to a PCB, Segger
zł521.14
1 weeks
No product available!
Standard 20-pin 0.1 male connector to provide electrical isolation, Segger
zł1,023.73
24h
Available quantity: 4
Available
J-Link ARM-14 Adapter, RoHS
zł354.39
24h
Available quantity: 1
Available
J-Link 19-pin Cortex-M Adapter, RoHS, Segger
zł164.33
24h
Available quantity: 3
Available
J-Link 9-pin Cortex-M Adapter, RoHS, Segger
zł166.12
24h
Available quantity: 2
Available
No product available!
J-Link 14-pin TI Adapter, RoHS, Segger
zł255.37
24h
Available quantity: 1
Available
No product available!
The Segger J-Link Signal Smoothing Adapter (8/06/12) is designed to improve signal integrity between the J-Link debug probe and the target debug device. It allows JTAG signals to be suppressed by adjustable series resistors, preventing excessive gain and jitter.
zł260.56
1 weeks
No product available!
The Segger J-Link Measurement+Patch Adapter allows you to easily customize connections between J-Link or Flasher devices and boards that do not have a standard debug connector. It is equipped with colored wires for signal identification, test points and jumpers for adjusting the voltages on the pins.
zł521.14
1 weeks
No product available!
The Segger J-Link Supply Adapter (8.06.14) allows you to manually set the debug probe I/O voltage, preventing damage to the target board, adjustable from 1.2V to 5.0V. It can be inserted between J-Link or Flasher and the target device, reducing the number of connections needed, which is especially useful in a production environment.
zł349.78
24h
Available quantity: 1
Available
The Intel FPGA Adapter (formerly J-Link Altera Adapter) connects to the Intel FPGA 10-pin JTAG connector, enabling debugging of FPGA-based MCU cores such as the dual-core Arm Cortex-A9 in Cyclone V devices. on Intel FPGA solutions.
zł254.71
1 weeks
No product available!
J-Link 6-pin Needle Adapter (8.06.16)
zł544.74
24h
Available quantity: 5
Available
The Segger J-Link Mictor 38 Adapter allows connection to a 38-pin Mictor connector in accordance with the ARM "ETM" specification. The adapter connects the GND and JTAG pins to the 20-pin J-Link, and the trace pins on the Mictor connector are not used.
zł787.02
1 weeks
No product available!
10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini
zł34.42
24h
Available quantity: 219
Available
An advanced tool that enables the integration of J-Link support into your own applications, used in both development environments and custom production tools. Supports debugging, flash programming, and application testing, offering support for Windows, Linux, and macOS, as well as compatibility with many programming languages via a DLL or shared library. Segger J-Link SDK (08.08.06)
zł10,528.97
1 weeks
No product available!
A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)