SEGGER (Q)SPI Flash Evaluator Adapter board Pack for BGA (6.40.02)

Segger Arduino MKR adapter (8.06.37) with 6-pin 0.05" and 20-pin JTAG connectors, designed for connecting Segger programmers and debuggers, enables efficient programming and testing of Arduino MKR boards.

Adapter enabling connection of Flasher PRO programmers and other Flasher models to devices with a 10-pin Renesas connector. It is compatible with M16C, M32C, R8C and R32C microcontrollers, providing stable communication and easy integration with older and modern programming systems. Segger Renesas M16C Family 10-Pin Adapter (8.06.40)

A 1:1 adapter that allows you to connect a standard 20-pin connector to its 2mm pitch counterpart without any additional configuration. For some models, such as the J-Link PRO, pins 14, 16, 18 and 20 may not be connected to ground, so it is recommended to leave them unconnected on the target hardware. Segger 2mm Adapter (06/08/11)

Adapter enabling connection of J-Link and Flasher debugging devices with a 20-pin 0.1" connector to a 14-pin 0.05" connector compliant with the ST standard. Segger STDC 14 Adapter (8.06.39)

Xilinx adapter that connects to Xilinx\'s 14-pin, 2mm JTAG connector, providing debugging of MCU cores such as the Arm Cortex-A9 on Xilinx Zynq FPGAs. With its compact design and high signal quality, it is a reliable tool for engineers working with FPGA platforms. Segger Xilinx Adapter (06/08/19)

A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)

J-Link TI-CTI-20 Adapter, RoHS, Segger

Adapter from the standard 20-pin 2.54 mm connector to the 10-pin 1.27 mm connector often used in Cortex-M boards. Segger 50-Mil 10-Pin Patch Adapter (8.06.28)

The Segger J-Link Measurement+Patch Adapter allows you to easily customize connections between J-Link or Flasher devices and boards that do not have a standard debug connector. It is equipped with colored wires for signal identification, test points and jumpers for adjusting the voltages on the pins.

Standard 20-pin 0.1 male connector to provide electrical isolation, Segger

Adapter providing two dedicated supply voltages - for programming and powering for the target board. Useful for programming modules that do not support low voltage programming or require a voltage other than 5V. Segger Programming Voltage Adapter (8.06.30)

J-Link SDK one year Support and Update Agreement extension. Can only be purchased by customers with a J-Link SDK License (Model 8.08.06). Segger J-Link SDK Extension (8.08.18)

A set of three adapters for SO-8, SO-8W and SO-16 memories that allows easy testing and programming of flash devices in these packages, eliminating the need for dedicated solutions for each form factor. The adapters are compatible with the SEGGER (Q)SPI Flash Evaluator and other test systems, making them a versatile tool for both test and production. SEGGER (Q)SPI Flash Evaluator Adapter Board Pack for SO-8, SO-8W, SO-16 (6.40.01)

The Segger J-Link Microchip Adapter (8/06/09) provides a debug connection between a J-Link probe and hardware with Microchip PIC32 series microcontrollers. Supports RJ12 debug connector, 14-pin MIPS connector and 6-pin PICkit connector.

An adapter that allows the J-Link device to connect to Microchip microprocessors that use an RJ11 debug connector, converting the standard 20-pin .1" connector to a 6-pin RJ11 connector. With this tool, users can take full advantage of 2-wire JTAG debugging capabilities, including process tracing, memory analysis, and real-time device control, and the 21 cm RJ11 cable provides convenience in connecting to the target system. Segger Microchip 2-Wire JTAG TDI Adapter (06/08/23)

An adapter that converts a standard 20-pin 2.54 mm connector to a 10-pin 2.54 mm connector. It enables the connection of Segger programmers with Silicon Labs devices and development boards with a C2 interface. Segger SiLabs C2 Adapter (8.06.17)