Microchip 2-Wire JTAG TDI Adapter (8.06.23)

RS232 module used as a communication extension equipped with a female DSUB9 connector, allowing easy connection to a PC or USB-RS232 adapter. Segger emPower RS232 Add-On (6.32.32)

J-Link 9-pin Cortex-M Adapter, RoHS, Segger

A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)

Adapter enabling easy connection of a Microchip AVR microcontroller device with the SEGGER Flasher programming system, supporting 6-pin and 10-pin connectors and providing fast connection via SPI protocol. With the function of powering the target hardware (3.3V or 5V) and direct power supply via VTREF connection, the adapter is flexible, easy to use and ideal for programming and debugging AVR microcontrollers in embedded systems, providing reliable communication and high precision. Segger AVR SPI Adapter (8.06.25)

Advanced evaluation board designed for rapid implementation of embedded solutions. Supporting the embOS operating system and SEGGER tools such as emFile, emWin, emUSB and emNet, the board is an ideal platform for software testing and application development in an environment based on the Xilinx Zynq XC7Z007S SoC with ARM Cortex-A9 processor and Artix7 FPGA. Segger emPower Zynq (6.31.00)

SiFive-ARTY adapter for debugging between J-Link and the ARTY board with SiFive RISC-V. Segger SiFive-ARTY Adapter (8.06.24)

A set of three BGA adapters enables easy testing and programming of flash devices in these packages, eliminating the need for dedicated solutions for each form factor. The adapters are compatible with the SEGGER (Q)SPI Flash Evaluator and other test systems, making them a versatile tool for both test and production. SEGGER (Q)SPI Flash Evaluator Adapter board Pack for BGA (6.40.02)

A compact adapter that provides direct pin compatibility, allowing easy replacement of standard IDC cable without changing the pinout. It is designed to work with devices such as the J-Link PLUS Compact, J-Link BASE Compact and Flasher Compact, enabling flexible and efficient debugging and programming configurations in embedded systems. Segger Right Angle (RAFF) Adapter (8.06.32)

Standard 20-pin 0.1 male connector to provide electrical isolation, Segger

A specialized demonstration board designed to support Tail Tagging within the embOS/IP IP stack. Using this technology, it is possible to transform a single Ethernet port into several logical ports, enabling the creation of a virtual multiport network using only a single Ethernet port. Segger embOS/IP Switch Board (6.70.00)

Standard 20-pin 0.1 male connector to provide electrical isolation, Segger

Adapter enabling connection of OCDS DAP interface to systems based on Infineon Aurix™ TC2xx, TC3xx, TC4xx and C167 microcontrollers. Converts standard 20-pin SEGGER connector to 10-pin 0.05\'\' Samtec FTSH, providing stable and reliable communication in debugging and programming processes. Segger Infineon Aurix DAP-10 Adapter (8.06.38)

An adapter that allows you to connect a 20-pin 0.1" connector to a 10-pin connector, allowing you to easily connect J-Link or Flasher programmers to your PCB using through-wires. It is ideal for prototyping, testing new designs and working with ST Discovery boards, offering flexibility, speed and time savings when making design changes.Segger Flying Wire Adapter (06.08.27)

Power adapter providing a stabilized 5V supply voltage for the target board. Segger 5V Target Supply Adapter (8.06.29)

The Segger J-Link Microchip Adapter (8/06/09) provides a debug connection between a J-Link probe and hardware with Microchip PIC32 series microcontrollers. Supports RJ12 debug connector, 14-pin MIPS connector and 6-pin PICkit connector.

Compact development board with NXP LPC54605J512 microcontroller, ideal for prototyping and testing USB solutions, equipped with two USB-Host ports and support for SEGGER software such as emUSB-Host, emLoad and embOS. Thanks to the simple firmware update process and the built-in J-Link OB debugger, the board allows you to quickly and conveniently start working with USB devices in embedded projects. Segger emPower-USB-Host (6.90.00)