Renesas M16C Family 10-Pin Adapter (8.06.40)

Adapter that converts standard 20-pin 2.54 mm connector to SWIM connector and 10-pin connector. Used for programming STM8 chips. Segger STM8 Adapter (8.06.22)

J-Link 9-pin Cortex-M Adapter, RoHS, Segger

J-Link 6-pin Needle Adapter (8.06.16)

SiFive-ARTY adapter for debugging between J-Link and the ARTY board with SiFive RISC-V. Segger SiFive-ARTY Adapter (8.06.24)

Adapter that enables JTAG connection between devices such as J-Link, J-Trace or Flasher and Jacinto7 systems from TI, offering access to JTAG/SWD and Trace connectors with TPIU tracking function. Thanks to high quality of workmanship and versatility, the adapter provides a stable connection, supporting debugging, testing and diagnostic processes in embedded systems. Segger MIPI-60 Adapter (8.06.42)

Professional reference board with ARM Cortex-M4F microcontroller, designed for code tracing and real-time application analysis. Equipped with an external 19-pin debug port and test points for trace signals, it enables easy integration with J-Link and J-Trace programmers, supporting Embedded Trace Macrocell (ETM) technology. Segger Cortex-M Trace Reference Board (6.68.18)

An adapter that allows the J-Link device to connect to Microchip microprocessors that use an RJ11 debug connector, converting the standard 20-pin .1" connector to a 6-pin RJ11 connector. With this tool, users can take full advantage of 2-wire JTAG debugging capabilities, including process tracing, memory analysis, and real-time device control, and the 21 cm RJ11 cable provides convenience in connecting to the target system. Segger Microchip 2-Wire JTAG TDI Adapter (06/08/23)

A 1:1 adapter that allows you to connect a standard 20-pin connector to its 2mm pitch counterpart without any additional configuration. For some models, such as the J-Link PRO, pins 14, 16, 18 and 20 may not be connected to ground, so it is recommended to leave them unconnected on the target hardware. Segger 2mm Adapter (06/08/11)

RS232 module used as a communication extension equipped with a female DSUB9 connector, allowing easy connection to a PC or USB-RS232 adapter. Segger emPower RS232 Add-On (6.32.32)

J-Link 19-pin Cortex-M Adapter, RoHS, Segger

A set of three adapters for SO-8, SO-8W and SO-16 memories that allows easy testing and programming of flash devices in these packages, eliminating the need for dedicated solutions for each form factor. The adapters are compatible with the SEGGER (Q)SPI Flash Evaluator and other test systems, making them a versatile tool for both test and production. SEGGER (Q)SPI Flash Evaluator Adapter Board Pack for SO-8, SO-8W, SO-16 (6.40.01)

Adapter enabling connection of OCDS DAP interface to systems based on Infineon Aurix™ TC2xx, TC3xx, TC4xx and C167 microcontrollers. Converts standard 20-pin SEGGER connector to 10-pin 0.05\'\' Samtec FTSH, providing stable and reliable communication in debugging and programming processes. Segger Infineon Aurix DAP-10 Adapter (8.06.38)

The Segger J-Link Measurement+Patch Adapter allows you to easily customize connections between J-Link or Flasher devices and boards that do not have a standard debug connector. It is equipped with colored wires for signal identification, test points and jumpers for adjusting the voltages on the pins.

The Intel FPGA Adapter (formerly J-Link Altera Adapter) connects to the Intel FPGA 10-pin JTAG connector, enabling debugging of FPGA-based MCU cores such as the dual-core Arm Cortex-A9 in Cyclone V devices. on Intel FPGA solutions.

A device that provides electrical isolation between the J-Trace emulator and the ARM board, which protects against electrical interference, especially in systems where the development tools and the application do not share the same ground. It provides 1 kV DC isolation, supports trace frequencies up to 75 MHz, and is compatible with J-Trace V2 and later versions, with a minimum power consumption of 25 µA. Segger J-Trace Isolator (07/08/10)

Segger Arduino MKR adapter (8.06.37) with 6-pin 0.05" and 20-pin JTAG connectors, designed for connecting Segger programmers and debuggers, enables efficient programming and testing of Arduino MKR boards.