New products
New products New products
zł301.74
24h
Dostępny
Available
Available
zł59.04
24h
Available
ST-LINK/V2 (Mini) Programmer - Waveshare 10053
ID: 569530
5906623465583
zł39.18
Tax included
zł31.85 tax excl.
Mini ST-LINK/V2, in-circuit debugger/programmer for STM8 and STM32
Description
Mini ST-LINK/V2 on a small single board, an extreme low cost solution for in-circuit debugger/programmer for STM8 and STM32.
Features
- Onboard 500mA self-recovery fuse to avoid harming by short circuit
- Dual voltage output (3.3V/5V), easy for debugging/programming
- Standard USB interface for direct connection to PC
- Debugging/Programing performance
- Debugging : run at full-speed, single-stepped, breakpoints, viewing variables and registers, etc.
- Programming : supports FLASH ROM, EEPROM, AFR, etc.
- USB2.0 combined with SWIM/SWD interfaces : quick response for debugging & fast speed for programming
- Upgradable firmware
- The firmware is upgradable to support more devices in the future
- Automatically upgraded
- Supported software
- ST-LINK Utility v2.0 (or higher ver.)
- STVD Version 4.2.1 (or higher ver.)
- STVP Version 3.2.3 (or higher ver.)
- IAR EWARM Revision v6.20 (or higher ver.)
- IAR EWSTM8 Revision v1.30 (or higher ver.)
- KEIL RVMDK Revision v4.21 (or higher ver.)
- ATOLLIC
- TASKING
- Supported devices
- All the STM8 devices with SWIM interface
- All the STM32 devices with SWD interface
ST-LINK/V2 (mini) Vs ST-LINK/V2 Vs ST-LINK
| Compare | ST-LINK/V2 (mini) | ST-LINK/V2 | ST-LINK | Remarks |
|---|---|---|---|---|
| SWD voltage range | 1.65V - 3.6V | 1.65V - 3.6V | 3V - 3.6V | ST-LINK/V2 and ST-LINK/V2 (mini) support STM32 low voltage devices |
| SWIM voltage range | 1.65V - 5.5V | 1.65V - 5.5V | 1.65V - 5.5V | |
| Supports SWV | NO | YES | NO | For the moment, only STM32 supports SWV while STM8 doesn't |
| Debug interfaces | 2 | 2 | 1 | ST-LINK/V2 and ST-LINK/V2 (mini) support STM8/STM32 with separated interfaces |
| LED indicator | Dual color LED | Dual color LED | Red LED | Dual color LED allows indicating more status |
| Fuse | YES | NO | NO | Fuse for avoid harming by short circuit |
Connecting with PC
While connecting the ST-LINK/V2 (mini) to the computer through USB interface, the USB driver is required and should be installed correctly first.
Connection with STM8/STM32 applications
The ST-LINK/V2 (mini) should be connected to the STM8 application via the SWIM interface.
| Debugger Pin | Target Board Pin | Description |
|---|---|---|
| VCC | MCU VCC | STM8 VCC |
| SWIM | MCU SWIM | STM8 SWIM PIN |
| GND | GND | STM8 GND |
| RST | MCU RESET | STM8 RESET PIN |
The ST-LINK/V2 (mini) should be connected to the STM32 application via the SWD interface.
| Debugger Pin | Target Board Pin | Description |
|---|---|---|
| VCC | MCU VCC | STM32 VCC |
| SWDIO | MCU SWDIO | STM32 SWD SWDIO |
| GND | GND | STM32 GND |
| SWCLK | MCU SWCLK | STM32 SWD SWCLK |
Please note that the VCC and GND should be connected correctly to avoid any harm to the ST-LINK/V2 (mini).
Package content
Weight: 0.01 kg
- ST-LINK/V2 (mini) × 1
- 4-pin custom connector cable × 1
- USB type A plug to receptacle cable × 1
569530
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 microcontrollers
Regular pricezł113.48zł104.99
24h
Available quantity: 35
Available
ST-LINK/V2-ISOL in-circuit debugger/programmer for STM8 and STM32 microcontrollers with digital isolation, STM, RoHS
zł420.62
24h
Available quantity: 15
Available
A new programmer-debugger with the USB interface. It supports the STM32 microcontrollers via SWD interface. ZL30PRGv2-1 is compatible with the STMicroelectronics ST-Link/V2-1. It also has the function of USB-UART converter, thanks to which it can successfully replace the KAmodRS module.
zł79.00
24h
Available quantity: 222
Available
Other products in the same category (16)
J-LINK EDU Mini is a version of the J-Link EDU (8.08.90) in a reduced form factor with identical functionality for Cortex-M based targets. It has been designed to allow students and educational facilities as well as hobbyists access to top of the line debug probe technology. Version for non-commercial use only. J-Link EDU mini
zł267.96
24h
Available quantity: 23
Available
A tool for programming and debugging applications for systems with the ARM Cortex-M and ARM Cortex-A core. It uses an embedded GDB server that is emulated via USB. Adafruit 3839
zł552.41
4 weeks
No product available!
JTAG interface for microcontrollers with ARM core
zł42.39
24h
Available quantity: 27
Available
JTAG / SWD programmer-debugger with USB and WiFi interface. It supports microcontrollers and microprocessors with Cortex-M, Cortex-A, Cortex-R and ARM7, ARM9 and ARM11 cores of most manufacturers as well as 8051, RISC-V, PIC32, RX. Segger J-Link WiFi (8.14.28)
zł5,180.26
24h
Available quantity: 2
Available
ST-LINK/V2-ISOL in-circuit debugger/programmer for STM8 and STM32 microcontrollers with digital isolation, STM, RoHS
zł420.62
24h
Available quantity: 15
Available
ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 microcontrollers
Regular pricezł113.48zł104.99
24h
Available quantity: 35
Available
Available
Compact tool for debugging and programming STM32 microcontrollers via JTAG / SWD interfaces. STMicroelectronics STLINK-V3MINIE
zł63.79
24h
Available quantity: 35
Available
Hi-Speed JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
zł4,177.46
24h
Available quantity: 2
Available
A new programmer-debugger with the USB interface. It supports the STM32 microcontrollers via SWD interface. ZL30PRGv2-1 is compatible with the STMicroelectronics ST-Link/V2-1. It also has the function of USB-UART converter, thanks to which it can successfully replace the KAmodRS module.
zł79.00
24h
Available quantity: 222
Available
JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
zł3,117.30
24h
Available quantity: 2
Available
A tool for debugging and programming STM32 microcontrollers via JTAG/SWD interfaces. It has a built-in current measurement unit (SMU) designed to optimise power consumption. STMicroelectronics STLINK-V3PWR
zł442.95
1 weeks
No product available!
No product available!
An adapter dedicated to programming STM32 microcontrollers in QFP100 chassis. It has a 20-pin JTAG/SWD connector and/or a 4-pin USART1 interface for programming and testing. Waveshare STM32-QFP100
zł355.27
24h
Available quantity: 1
Available
RLink-STD is a versatile programmer and debugger for STM8 and ARM microcontrollers, enabling unlimited programming and partial application debugging in the Ride7 environment. It supports JTAG, SWD, SWIM, and ICC, making it a suitable tool for working with a wide range of embedded systems.
Regular pricezł679.01zł579.00
24h
Available quantity: 2
Available
Adapter with galvanic isolation for STLINK-V3SET. It also allows the programmer to work with systems powered with voltages below 3.3 V. STMicroelectronics B-STLINK-ISOL
zł195.61
24h
Available quantity: 1
Available
Mini ST-LINK/V2, in-circuit debugger/programmer for STM8 and STM32