STLINK-V3SET - STLINK-V3 modular in-circuit debugger and programmer for STM32/STM8
ID: 572910
5906623436255
zł172.43
Tax included
zł140.19 tax excl.
The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and a complementary adapter board
Description
The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and a complementary adapter board.
The SWIM and JTAG/SWD interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.
The STLINK-V3SET also provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller through one UART, and bridge interfaces (SPI, I2C, CAN, GPIOs) allowing for instance the programming of the target through bootloader.
The modular architecture of STLINK-V3SET enables to extend its main features through additional modules such as the adapter board.
Features
- Stand-alone probe with modular extensions
- Self-powered through a USB connector (Micro-B)
- USB 2.0 high-speed compatible interface
- Direct firmware update support (DFU)
- JTAG / serial wire debugging (SWD) specific features:
- 3 V to 3.6 V application voltage support and 5 V tolerant inputs
- Flat cables STDC14 to MIPI10 / STDC14 / MIPI20 (connectors with 1.27 mm pitch)
- JTAG communication support
- SWD and serial wire viewer (SWV) communication support
- SWIM specific features (only available with adapter board MB1440):
- 1.65 V to 5.5 V application voltage support
- SWIM header (2.54 mm pitch)
- SWIM low-speed and high-speed modes support
- Virtual COM port (VCP) specific features:
- 3 V to 3.6 V application voltage support on the UART interface and 5 V tolerant inputs
- VCP frequency up to 15 MHz
- Available on STDC14 debug connector (not available on MIPI10)
- Multi-path bridge USB to SPI/UART/I2C/CAN/GPIOs specific features:
- 3 V to 3.6 V application voltage support and 5 V tolerant inputs
- Signals available on adapter board only (MB1440)
- Drag-and-drop Flash programming
- Two color LEDs: communication, power
Included
- Programmer
- Adapter Module
- Three Flat Cables
- BLS Cables
- Housing
- Mounting Key
572910
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32 microcontrollers
Regular pricezł113.38zł104.89
24h
Available quantity: 18
Available
ST-LINK/V2-ISOL in-circuit debugger/programmer for STM8 and STM32 microcontrollers with digital isolation, STM, RoHS
zł420.62
24h
Available quantity: 15
Available
Other products in the same category (16)
JTAG interface for microcontrollers with ARM core
zł42.39
24h
Available quantity: 27
Available
A new programmer-debugger with the USB interface. It supports the STM32 microcontrollers via SWD interface. ZL30PRGv2-1 is compatible with the STMicroelectronics ST-Link/V2-1. It also has the function of USB-UART converter, thanks to which it can successfully replace the KAmodRS module.
zł79.00
24h
Available quantity: 225
Available
Available
Compact tool for debugging and programming STM32 microcontrollers via JTAG / SWD interfaces. STMicroelectronics STLINK-V3MINIE
zł63.79
24h
Available quantity: 50
Available
Hi-Speed JTAG/SWD Emulator with USB and Ethernet interface, Segger
zł5,221.25
24h
Available quantity: 3
Available
Debugger/programmer with a USB interface that supports the SWD (Serial Wire Debbug) programming interface. It is based on CMSIS-DAP (Coresight Debug Access Port) and also has a USB-UART converter function
zł59.90
24h
Available quantity: 16
Available
10-wire ribbon cable (1.27mm to 2.54mm) for Segger J-Link EDU mini
zł34.42
24h
Available quantity: 238
Available
Adapter with galvanic isolation for STLINK-V3SET. It also allows the programmer to work with systems powered with voltages below 3.3 V. STMicroelectronics B-STLINK-ISOL
zł195.61
24h
Available quantity: 1
Available
JTAG/SWD debug probe with USB interface. Based on a 32-bit RISC CPU, it can communicate at high speed with the supported target CPUs. J-Link is used around the world in tens of thousand places for development and production (flash programming) purposes. J-link PLUS Compact (8.19.28)
zł3,113.34
24h
Available quantity: 3
Available
Mini ST-LINK/V2, in-circuit debugger/programmer for STM8 and STM32
zł39.18
24h
Available quantity: 43
Available
No product available!
Hi-Speed JTAG/SWD Emulator for ARM7/9, Cortex and Renesas RX cores with USB interface, Segger
zł4,177.46
24h
Available quantity: 2
Available
JTAG / SWD programmer-debugger with USB and WiFi interface. It supports microcontrollers and microprocessors with Cortex-M, Cortex-A, Cortex-R and ARM7, ARM9 and ARM11 cores of most manufacturers as well as 8051, RISC-V, PIC32, RX. Segger J-Link WiFi (8.14.28)
zł5,180.26
24h
Available quantity: 2
Available
An adapter dedicated to programming STM32 microcontrollers in QFP100 chassis. It has a 20-pin JTAG/SWD connector and/or a 4-pin USART1 interface for programming and testing. Waveshare STM32-QFP100
zł355.27
24h
Available quantity: 1
Available
A tool for debugging and programming STM32 microcontrollers via JTAG/SWD interfaces. It has a built-in current measurement unit (SMU) designed to optimise power consumption. STMicroelectronics STLINK-V3PWR
zł442.95
24h
Available quantity: 3
Available
A tool for programming and debugging applications for systems with the ARM Cortex-M and ARM Cortex-A core. It uses an embedded GDB server that is emulated via USB. Adafruit 3839
zł552.41
4 weeks
No product available!
The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and a complementary adapter board