KAmod BlackPill 401 - Evaluation board, soldered joints from above
ID: 1195712
5906623496631
zł35.61
Tax included
zł28.95 tax excl.
The KAmod BlackPill 401 is an evaluation board with an STM32F401CCU microcontroller, featuring USB-C with ESD protection and a modified power circuit. With a pre-installed bootloader, it supports Arduino IDE, offering 32 GPIOs and versatile programming capabilities
Description
The KAmod BlackPill 401 evaluation board features the STM32F401CCU microcontroller along with essential components for its operation and programming. While pin-compatible with the BlackPill project, this is a completely new design featuring a USB-C connector with ESD protection and a modified power circuit. With a pre-installed bootloader, it supports programming via Arduino IDE.
Features
- Microcontroller: STM32F401CCU6: Cortex-M4, 256 kB Flash, 64 kB RAM, 84 MHz, 1 x 12-bit ADC, 7 timers, 3 x I2C, 2 x SPI, 3 x UART, USB OTG FS, RTC
- USB-C Connector: Functions as a power supply, USB communication interface, and programming port
- Filtering Components: Protects against noise and surges on USB interface lines
- GPIO and Power Lines: 32 GPIO pins and 5V/3.3V power lines available on 2.54 mm pitch connectors
- Load Capacity: 5V line: 500 mA; 3.3V line: 200 mA
- Clocking: Precise resonator for the microcontroller and a separate resonator for RTC
- RTC Backup: Supports an external battery for RTC backup
- Programming/Debugging: SWD interface for debugging and compatibility with STM32CubeProgrammer and Arduino IDE
- Dimensions: 56 x 23 mm; height approx. 13 mm (with soldered goldpin headers from above)
Included
- Fully assembled module with a pre-installed bootloader and soldered goldpin headers.
1195712
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Other products in the same category (16)
The starter kit is equipped with a STM32F373VCT6 microcontroller (256 MB Flash, Cortex-M4), with a built-in ST-Link / V2 programmer-debugger, has a TFT LCD display and a full set of connectors.
zł1,817.46
1 weeks
No product available!
A compact reference platform that enables rapid testing and verification of trace configurations, providing excellent signal quality for analysis. With the ST STM32H743 microcontroller and support for JTAG, SWD and SWO debugging interfaces, the board provides high performance and flexibility in monitoring system performance. Segger STM32H7 Trace Reference Board (6.68.20)
zł1,036.19
1 weeks
No product available!
The STM32U5G9J-DK1 is an advanced discovery kit with the STM32U5G9NJH6Q microcontroller, designed for rapid prototyping and evaluation of STM32U5-based applications. The kit offers a wide range of peripherals, such as USB, a TFT-LCD touchscreen display, and Arduino™ and STMod+ compatible connectors, making it ideal for developing IoT applications and portable devices.
zł477.06
24h
Available quantity: 2
Available
Evaluation kit for the STM32L476ZGT6 microcontroller based on the STMicroelectronics ARM Cortex-M4 core. Equipped with three I²C buses, three SPI interfaces, six USART ports, CAN port, SWPMI, two SAI ports, 12-bit ADC converter, 12-bit DAC converter, LCD controller, internal memory and LCD controller. STMicroelectronics STM32L476G-EVAL
zł1,599.42
1 weeks
No product available!
The KAmod BlackPill 411 is an evaluation board featuring the STM32F411CEU microcontroller, offering versatile programming capabilities with a USB-C connector and a pre-installed bootloader compatible with Arduino IDE. Equipped with 32 GPIOs, a modified power circuit, and ESD protection, it is perfect for embedded projects.
zł36.43
24h
Available quantity: 138
Available
Evaluation kit equipped with STM32F411CEU6 microcontroller (ARM Cortex M4, 100MHz, 512kB Flash, 128kB RAM). It has two 20-pin connectors enabling the use of numerous microcontroller peripheral systems.
zł38.35
24h
Available quantity: 13
Available
Development kit with STM32L496ZGT6 microcontroller with built-in ST-Link programmer. Extensive equipment, including: MEMS 6DoF sensor, motor controller, joystick, LED display, 8 LED diodes, RGB LED, audio amplifier, Flash memory QSPI 1 MB, microphone.
zł249.00
24h
Available quantity: 32
Available
Waveshare Core429I is a PCB with STM32F429IGT6 microcontroller, contains necessary elements for microcontroller operation, all GPIOs connected to goldpin connectors
zł372.65
4 weeks
No product available!
Test board for testing the emFile NAND controller and compatible memory devices. The base module with the STM32H743 microcontroller works with interchangeable adapters supporting different NAND Flash packages, providing flexibility in testing. Segger NAND Flash Evaluator (6.20.12)
zł1,297.86
1 weeks
No product available!
Development kit with STM32L496ZGT6 microcontroller (ARM Cortex-M4 core) with a built-in ST-Link programmer. Extensive equipment, including: MEMS 6DoF sensor, motor controller, joystick, LED display, 8 LED diodes, RGB LED, audio amplifier, Flash memory QSPI 1 MB, microphone, Arduino connector
zł281.04
24h
Available quantity: 28
Available
Development board with STM32H725AE microcontroller dedicated to applications combining image processing with artificial intelligence. Seeed Studio 102110607
zł187.61
4 weeks
No product available!
The KAmod BlackPill 401 is an evaluation board with an STM32F401CCU microcontroller, featuring USB-C with ESD protection and a modified power circuit. With a pre-installed bootloader, it supports Arduino IDE, offering 32 GPIOs and versatile programming capabilities
zł36.90
24h
Available quantity: 42
Available
Kamod BluePill+ - Evaluation board with STM32F103C8T6 microcontroller, compatible with BluePill -...
The Kamod BluePill+ evaluation board equipped with the STM32F103C8T6 microcontroller offers improvements over the original BluePill, such as a new PCB design, a USB-C connector with ESD protection, an improved power supply circuit, and the ability to program via Arduino IDE and STM32CubeIDE
zł21.67
24h
Available quantity: 57
Available
The Wio-E5 STM32WLE5JC module with LoRa SX126x enables the creation of energy-efficient, long-range IoT solutions with LoRaWAN® support in the EU868, US915, and other bands. Equipped with peripheral interfaces and AT firmware, it ensures fast integration in industrial and environmental applications. Available in tape (cut tape/reel), optimized for production. Seeed Studio 317990829
zł39.90
4 weeks
No product available!
The board is equipped with the STM32F405 microcontroller with the ARM Cortex-M4 core and SPI Flash memory, 20 GPIO pins, SD card slot, pins for connecting the battery with the charging and voltage stabilization circuit, JTAG connector and Qwiic socket. SparkFun DEV-17712
zł149.38
24h
Available quantity: 2
Available
The STM32L4R9I-EVAL evaluation set was designed to demonstrate the capabilities of the STM32L4R9AI microcontroller. Mounted connectors allow easy connection of extensions. The board also has a debugger / ST-LINK / V2-1 programmer. STM32L4R9I-EVAL
zł1,722.00
1 weeks
No product available!
The KAmod BlackPill 401 is an evaluation board with an STM32F401CCU microcontroller, featuring USB-C with ESD protection and a modified power circuit. With a pre-installed bootloader, it supports Arduino IDE, offering 32 GPIOs and versatile programming capabilities