KAmodPCAL6408 - 8-channel I2C expander module
ID: 586091
5906623432837
zł16.90
Tax included
zł13.74 tax excl.
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.
Description
KAmodPCAL6408 is an 8-bit I/O expander with I2C control. It has 8 GPIO outputs/inputs. The module has the ability to select the address of the system, so that 2 such modules can be connected to one bus. The board is equipped with a standard Pmod I2C connector and a KAMAMI connector, allowing for easy connection of the module to the development kits. Thanks to its small dimensions, the product can be used in many development projects, while the Pmod straight-through connector allows you to connect boards in rows.
Properties
- NXP PCAL6408A chip
- 8 programmable inputs / outputs
- I2C bus
- Programmable interrupt output
- Ability to select chip address (0x20 or 0x21)
- Pass-through connector compatible with Pmod standard, allows for serial connection of Pmod I2C modules
- Connector compatible with KAMAMI standard
- Built-in pull-up jumpers on I2C bus lines
- Built-in jumper for connecting INT line of system to INT line of Pmod connectors
- Built-in I2C address selector
- Possibility to power supply with voltage in the range 1.7-5.5 V through the Pmod connector and 1.8-5.5 V through the KAMAMI connector
- Mounting holes 2.5mm in diameter
- Dimensions: 61.2 x 20.3 x 10mm
586091
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30
zł6.90
24h
Available quantity: 3
Available
Other products in the same category (16)
KAmodNFC is an expansion board with M24LR64E-R chip – dynamic tag with 64kb EEPROM memory and dual communication interface (I2C/RF). On board is placed also signalization of energy harvesting function, which is in M24LR64E-R chip embedded.
zł28.91
24h
Available quantity: 210
Available
Four relay output module for Raspberry Pi 4B, Pi 3B+ Pi3B, Pi2, Pi+, Pi minicomputers.
zł38.35
24h
Available quantity: 38
Available
KAmodMC3635 is a module with the MC3635 three-axis accelerometer from mCube. The sensor allows the measurement of acceleration in the range of ±2g/±4g/±8g/±12g/±16g, the measurement frequency is from 14 to 1300 Hz. Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMC3635
zł14.90
24h
Available quantity: 453
Available
A 30 cm long connecting cable (6 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF06S connector that KAmod modules are equipped with. cabhu06-30
zł9.90
24h
Available quantity: 192
Available
KAmodLIS35DE is a module with a three-axis LIS35DE accelerator from STMicroelectronics. The chip has a digital signal output (I2C or SPI bus) and allows acceleration measurement in three axes.
zł19.90
24h
Available quantity: 462
Available
Pressure sensor module with I2C interface (BMP085)
zł74.89
24h
Available quantity: 5
Available
zł5.90
24h
Available quantity: 480
Available
KAmodBT-HC05 is a Bluetooth module configured via AT commands. It has integrated LEDs indicating operating mode and connection status with the paired device, as well as a logic level translator on UART lines. KAmodBT-HC05
zł49.90
24h
Available quantity: 74
Available
KAmodMPL3115A2 is a module with an atmospheric pressure sensor MPL3115A2 from NXP. Sensor allows to make a measurement in the range of 200...1100hPa (20...110kPa). Communication with the sensor is realized via the I2C interface. The board is equipped with the Pmod I2C standard connector and the KAMAMI connector. Kamami KAmodMPL3115A2
zł27.90
24h
Available quantity: 192
Available
KAmodRPI RS485 CAN HAT is a shield for the Raspberry Pi computer that extends its interfaces with RS485 and CAN. Bus signals are led out to goldpin connectors and terminal blocks.
zł39.90
24h
Available quantity: 89
Available
Module of a stereo 24-bit audio converter with I2S interface (TS4657).
zł59.00
24h
Available quantity: 66
Available
The KAmodRS module is a reliable RS232-UART converter supporting voltages from 3 V to 5.5 V and enabling data transmission at a speed of up to 250 kbit/s. Thanks to the use of the MAX3232 chip, the module is ideal for a wide range of electronic and microcontroller applications requiring stable and effective serial communication
zł15.99
24h
Available quantity: 120
Available
Module with L3G4200D (3-axis gyroscope with digital output)
zł34.90
24h
Available quantity: 2
Available
Available
KAmodRPi-Pmod-HAT is a HAT for Raspberry Pi 5/4B/3B+/3B/2B/B+ minicomputers that allows use of the communication interfaces available on the 40-pin minicomputer connector
zł42.90
24h
Available quantity: 260
Available
A 30 cm long connecting cable (4 wires) designed for use with Kamami KAmod modules. It is terminated on both ends with a plug that fits the WF04S connector that KAmod modules are equipped with. cabhu04-30
zł6.90
24h
Available quantity: 3
Available
The KAmodPCAL6408 is an 8-bit I/O expander with the PCAL6408A chip by NXP, controlled by the I2C interface.