DFRobot Gravity Module with digital current sensor
ID: 573840
5906623406005
zł33.78
Tax included
zł27.46 tax excl.
A digital precision current sensor module that measures voltage, current and power of electronic modules and devices up to 26V and 8A with a relative error of ± 0.2%. DFRobot SEN0291
Free shipping
free shipping in Poland for all orders over 500 PLN
Same day shipping
If your payment will be credited to our account by 11:00
14 days for return
Each consumer can return the purchased goods within 14 days
Description
Gravity: I2C Digital Wattmeter is a module of a precision digital current sensor with the INA219 system from TI. The system enables measurement of voltage, current and power of electronic modules and devices in the range up to 26V and 8A with a relative error of ± 0.2%. Communication with the module takes place via the I2C interface. The product can be used to assess energy consumption or battery life in solar energy systems, batteries, motors, controllers or electronic modules.
properties
- Measured voltage range (IN + or IN- in relation to GND): 0 ... 26 V
- Voltage measurement resolution: 4 mV
- Current range: 0 ... ± 8A (two-way current)
- Current measurement resolution: 1mA
- Relative error: <± 0.2%
- Power measurement range: 0 ... 206 W
- Power measurement resolution: 4 mW
- Quiescent current: 0.7 mA
- Interface: I2C
- Gravity connector
- I2C Address: Four options 0x40, 0x41, 0x44, 0x45
- Input voltage (VCC): 3.3 ... 5.5 V
- Dimension: 30 x 22 mm
- Weight: 4 g
Sample module connection
Included
- Gravity Module: I2C Digital Wattmeter
- Connector XH2.54-4P
- Connecting cable Gravity-4P I2C / UART
573840
Data sheet
- Interface
- I2C
- Zakres pomiarowy
- ±8 A
- Sposób podłączenia
- Szeregowy
You might also like
A small current sense module with a digital SPI interface. The board combines an Allegro ACS722 Hall Effect current sensor with a 12-bit analog-to-digital converter. 410-325
Delivery date unknown
No product available!
Expansion board for Arduino, allows easy connection of XBee modules, has separate outputs for I2C, SPI and UART buses. The built-in 3.3V voltage stabilizer and operating mode switch make it easier to program the Arduino when the XBee module is connected to the sockets. DFRobot DFR0265
zł46.53
24h
Available quantity: 2
Available
Module with INA219 system with bi-directional current meter
zł11.62
Delivery date unknown
No product available!
Gravity: IO Expansion & Motor Driver Shield is an Arduino compatible expansion board that provides digital I / O ports, analog I2C, SPI and UART interfaces, as well as a DC motor driver. DFRobot DFR0502
zł71.64
24h
Available quantity: 4
Available
Module with bi-directional current sensor based on the INA226 system. It allows you to measure current and power, works with a voltage of 0-36 V. It has an I2C interface.
zł29.90
24h
Available quantity: 28
Available
Other products in the same category (16)
This board is a simple carrier of Broadcom’s bidirectional ±40A ACHS-7124 Hall effect-based linear current sensor, which offers a low-resistance (~0.7 mΩ) current path and electrical isolation up to 3 kV RMS. Pololu 4033
zł34.26
24h
Available quantity: 6
Available
Available
ACS714 Current Sensor Carrier -5 to +5A
zł115.02
24h
Available quantity: 1
Available
Analogue current sensor module. Allows measurement of AC and DC currents up to 50 A. DFRobot SEN0098-V2
zł73.89
24h
Available quantity: 3
Available
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 20 A. DFRobot SEN0211
zł98.45
24h
Available quantity: 2
Available
Module with ACHS-7123 current sensor with a measuring range of direct and alternating current from -30 to 30 A. It communicates via an analog interface. Pololu 4032
zł34.06
24h
Available quantity: 4
Available
Module with ACS724LLCTR-30AU current sensor with a measuring range of direct and alternating current from 0 to 30 A. It communicates via an analog interface. Pololu 4046
zł53.19
24h
Available quantity: 2
Available
The current measurement with the value 0-20A is carried out by the ACS712-05 system based on the Hall effect. The sensitivity of the system is 100mV / A (analogue signal) .modACS712-20
zł14.66
24h
Available quantity: 25
Available
INA169 current sensor module. The system can be supplied with the voltage from 2.7 V to 60 V and has an analog output. SparkFun SEN-12040
zł58.68
24h
Available quantity: 1
Available
The current measurement of 0 - 30A is carried out by the ACS712-30 system based on the Hall effect. The sensitivity of the system is 66mV / A (analog signal).
zł8.00
6 weeks
No product available!
Module with an analog AC current sensor in a set with a probe for non-contact measurement of alternating current with a current of up to 10 A. DFRobot SEN0288
zł108.03
24h
Available quantity: 12
Available
Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650
zł44.90
24h
Available quantity: 2
Available
ACS711EX Current Sensor Carrier -15.5A to +15.5A
zł15.90
24h
Available quantity: 2
Available
Available
Module with an analog current sensor. It enables the measurement of alternating and direct currents up to 50 A. Cytron BB-ACS756
zł82.51
24h
Available quantity: 4
Available
Module with ACS724LLCTR-05AB current sensor with a measuring range of direct and alternating current from -5 to 5 A. It communicates via an analog interface. Pololu 4041
zł47.71
24h
Available quantity: 5
Available
A digital precision current sensor module that measures voltage, current and power of electronic modules and devices up to 26V and 8A with a relative error of ± 0.2%. DFRobot SEN0291