Module with a stepper motor driver based on the DRV8834 system. It allows you to power a bipolar motor with a current of up to 2 A per phase, without using a heat sink. The system can be powered with a voltage of up to 10.8 V. Pololu 2134

DRV8834 Low-Voltage Stepper Motor Driver Carrier

Expansion board with L6474 stepper motor driver. It is equipped with a connector compatible with Arduino Uno R3 and STM32 Nucleo. STMicroelectronics X-NUCLEO-IHM01A1

The pad for use with shallow Feather series contains two TB6612 chips that allow you to control DC motors or stepper motors. The I2C interface is used to communicate with the overlay. Adafruit 2927

The expansion module is designed to work with micro:bit. It allows you to control 4 DC motors or two stepper motors and 8 servos. It communicates via the I2C interface. DFRobot DFR0548

A4988 Stepper Motor Driver Carrier with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Pololu 2981

Extension module with a driver for two stepper motors based on the HR8825 system. Dedicated for Raspberry Pi minicomputers. Waveshare Stepper Motor HAT (B)

Module with a 2-channel driver for DC motors L293D designed to work with the Raspberry Pi Pico. It can work with a voltage from 6 to 12 V and a current of up to 600 mA. SB Components 21468

TB67S249FTG stepper motor driver module supplied with 10-47V voltage and working current of 1.7A. The controller allows you to control the motor movement up to 7 different resolutions (up to 1/32 of a step). Pololu 2973

Compact stepper motor controller with the TMC2208 system with operating voltage from 4 to 35 V. It offers smooth, quiet operation, high efficiency, various operating modes and easy configuration. It is controlled via the STEP/DIR interface and is an ideal solution for 3D printers and similar applications

This Kit with fully-dedicated PWM driver chip handles all the motor and speed controls over I2C. Only two data pins (SDA & SCL in addition to the power pins GND & 5V) are required to drive the multiple motors; you can also connect any other I2C devices or shields to the same pins. This  makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3. Adafruit 1438

HAT module with TB6612FNG motor driver and PCA9685 PWM driver designed for Raspberry Pi minicomputers. The board is equipped with a 40-pin connector. Adafruit 4280

Shield with dual-channel DC motor driver for Arduino. It has an operating voltage from 7 to 30 V and a continuous current of up to 10 A. It can be controlled by a PWM signal or by means of built-in buttons. Cytron SHIELD-MDD10

This is a breakout board for ON Semiconductor’s AMIS-30543 microstepping bipolar stepper motor driver, which features SPI-adjustable current limiting, 11 step modes (from full-step through 1/128-step), back-EMF feedback that can be used for stall detection or optional closed-loop control, and over-current and over-temperature protection. 

The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC).

Module with a 2-channel DC motor driver TB6612FNG designed to work with micro: bit. It can also control 3 servos. SB Components 14897

Compact stepper motor controller with the TMC2130 system with operating voltage from 5.5 to 45 V. It offers smooth, quiet operation, high efficiency, various operating modes and easy configuration. It is controlled via the STEP/DIR interface and is an ideal solution for 3D printers and similar applications. BIGTREETECH TMC2130 V3.0

Two axis stepper motor driver expansion board based on the L6470 for STM32 Nucleo

Tic T500 USB is a stepper motor driver based on the MP6500 chip. It allows you to control the stepper motor whose voltage on the coil is 4.5-35V, the maximum current per coil is up to 1.5A. The controller can be controlled by: USB, TTL, I2C, RC (PWM model) etc. Pololu 3134

The stepper motor driver with the MP6500 system, allows the bipolar motor to be supplied with a current of up to 2A per phase, without the use of a heat sink. The system can be supplied with voltage in the range 4.5 ... 35V. Polol 2969