Pololu stepper motor driver module with TB67S128FTG system
ID: 577700
5906623479962
zł80.45
Tax included
zł65.41 tax excl.
TB67S128FTG stepper motor driver module powered by 6.5-44V voltage and 2.1A operating current. The controller allows you to control the movement of the engine with up to 8 different resolutions (up to 1/128 step). Pololu 2998
Description
Pololu stepper motor driver offers a micro step resolution of 1/128 degree and allows you to control one bipolar stepper motor at a speed of up to about 2.1 A per phase continuously (5 A peak) without a heat sink or forced air flow. The controller has a wide operating voltage range from 6.5 V to 44 V. It has a built-in protection against low voltage, overcurrent and overheating. It also has voltage reversal protection (up to 40 V). The product is delivered with all surface mount components installed. Soldering is required for the assembly of the included straight-through parts.
Features
- Based on the TB67S128FTG chip
- Step resolution: full, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128
- Motor supply voltage: 6.5 - 44 V
- Continuous current per phase: 2.1 A (temporary up to 5 A0
- Minimum logic voltage: 2 V
- Maximum logical voltage: 5.5 V
- Current limit control: potentiometer, digital input, via SPI interface
- Reverse voltage protection
- Module dimensions: 20 x 15 mm
- Weight: 5.7 g
Included
- TB67S128FTG Stepper Motor Driver Carrier
- 3 x screw connector 2 pin
- 2 x goldpin straight male connector
- jumper
577700
Data sheet
- Output current
- 2.1A
- Number of channels
- 2
- Supply voltage min
- 6,5 V
- Supply voltages max
- 44 V
Manufacturer BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
You might also like
This NEMA 17-size hybrid bipolar stepping motor has an integrated 28 cm (11″) threaded rod as its output shaft, turning it into a linear actuator capable of precision open-loop positioning. The stepper motor has a 1.8° step angle (200 steps/revolution) and each phase draws 1.7 A at 2.8 V, allowing for a holding torque of 3.7 kg-cm (51 oz-in). Pololu 2268
zł534.89
Delivery date unknown
No product available!
This NEMA 17-size hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 1.7 A at 2.8 V, allowing for a holding torque of 3.7 kg-cm (51 oz-in). Pololu 2267
zł220.60
24h
Available quantity: 2
Available
Other products in the same category (16)
The stepper motor driver with Allegro A4988 (A4988 Stepper Motor Driver Carrier) allows you to supply a bipolar current of up to 2A per phase. The system can be supplied with voltage up to 35V, in the set there is a heat sink. It is compatible with Polol 1182
zł5.20
24h
Available quantity: 11
Available
Simple to use stepper motor driver, compatible with anything that can output a digital 0..5V pulse or 0..3.3V pulse. Connect a 4-wire stepper motor and a microcontroller and you’ve got precision motor control! EasyDriver drives bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors. ROB-12779
zł87.16
3 weeks
No product available!
Black Edition offers adjustable current limiting, over-current and over-temperature protection, and five different microstep resolutions. It operates from 8 V to 35 V and can deliver up to 2 A per coil with sufficient additional cooling. Pololu 2128
zł39.90
24h
Available quantity: 1
Available
This is a breakout board for ON Semiconductor’s AMIS-30543 microstepping bipolar stepper motor driver, which features SPI-adjustable current limiting, 11 step modes (from full-step through 1/128-step), back-EMF feedback that can be used for stall detection or optional closed-loop control, and over-current and over-temperature protection.
zł98.82
24h
Available quantity: 1
Available
The Tic T825 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC).
zł170.43
24h
Available quantity: 1
Available
The Tic T825 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC).
zł172.99
4 weeks
No product available!
Stepper motor driver based on TB67S249FTG. It allows you to control a stepper motor with voltage from 10 to 47V, with a maximum current of 1.8A. The controller can be controlled using: USB, Serial TTL, I2C, RC (PWM modeling), analog input or quadrature encoder. Pololu 3138
zł252.80
4 weeks
No product available!
The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC).
zł287.59
24h
Available quantity: 3
Available
The Tic T834 USB Multi-Interface Stepper Motor Controller makes basic control of a stepper motor easy, with quick configuration over USB using our free software. The controller supports six control interfaces: USB, TTL serial, I²C, analog voltage (potentiometer), quadrature encoder, and hobby radio control (RC).
zł172.99
4 weeks
No product available!
DRV8825 Stepper Motor Driver Module for Arduino. It allows you to control two drives, equipped with an XBee connector. DFRobot DRI0023
zł159.16
24h
Available quantity: 1
Available
The stepper motor driver with the MP6500 system allows the bipolar motor to be supplied with current up to 1.5 A per phase, without the use of a heat sink. The system can be supplied with voltage in the range 4.5 ... 35 V. Pololu 2966
zł47.98
24h
Available quantity: 1
Available
MP6500 Stepper Motor Driver Carrier, Digital Current Control
zł44.44
24h
Available quantity: 1
Available
Tic T500 USB Multi-Interface Stepper Motor Controller
zł131.23
24h
Available quantity: 1
Available
Tic T500 USB is a stepper motor driver based on the MP6500 chip. It allows you to control the stepper motor whose voltage on the coil is 4.5-35V, the maximum current per coil is up to 1.5A. The controller can be controlled by: USB, TTL, I2C, RC (PWM model) etc. Pololu 3134
zł139.38
4 weeks
No product available!
TB67S279FTG stepper motor controller module supplied with 10 ... 47V voltage and 1.2A working current. The controller allows you to control the motor movement up to 7 different resolutions (up to 1/32 of a step). Pololu 2974
zł57.01
24h
Available quantity: 1
Available
TB67S249FTG stepper motor driver module supplied with 10-47V voltage and working current of 1.7A. The controller allows you to control the motor movement up to 7 different resolutions (up to 1/32 of a step). Pololu 2973
zł64.72
24h
Available quantity: 2
Available
TB67S128FTG stepper motor driver module powered by 6.5-44V voltage and 2.1A operating current. The controller allows you to control the movement of the engine with up to 8 different resolutions (up to 1/128 step). Pololu 2998