

zł69.84 tax excl.
Module with a 2-channel driver for DC motors L293D designed to work with the Raspberry Pi Pico. It can work with a voltage from 6 to 12 V and a current of up to 600 mA. SB Components 21468
Module with a 2-channel driver for DC motors L293D designed to work with the Raspberry Pi Pico. It can work with a voltage from 6 to 12 V and a current of up to 600 mA. It allows you to control the rotation of two DC motors or one stepper motor. The board has an ON/OFF switch and a voltage stabilizer that supplies the RPi Pico. Full documentation and examples of use are available on the product page.
Data sheet
Responsible person BTC Korporacja sp. z o. o. Lwowska 5 05-120 Legionowo Poland sprzedaz@kamami.pl 22 767 36 20
Module with the RP2040 microcontroller with two ARM Cortex-M0 + cores operating at 133 MHz, 256 kB RAM and 30 GPIO. The board also has 2 MB of external QSPI flash memory. Module can be programmed in C/C++ or microPython. Raspberry Pi Pico
Starter kit containing Raspberry Pi Pico, necessary connectors and a microUSB cable. The kit is recommended for people programming in MicroPython
Module with LCD IPS display, 1.14" diagonal and 240x135 px resolution. Communication via SPI interface. Waveshare Pico-LCD-1.14
No product available!
A pin expander for Raspberry Pi Pico boards. It is equipped with a standard female connector and four sets of male strips 2x20 pins. Waveshare Pico-Quad-Expander
A pin expander for Raspberry Pi Pico boards. It is equipped with a standard female connector and two sets of male strips 2x20 pins. Waveshare Pico-Dual-Expander
Uninterruptible power supply module for Raspberry Pi Pico, allowing you to continue working and safely shut down after a power failure. Waveshare Pico-UPS-B
Monochrome VGA camera module with HM0360 sensor working with Raspberry Pi Pico. It uses 1 bit video interface and I2C to configure the registers. ArduCAM B0319
2-channel module with relays designed to work with the Raspberry Pi Pico. It can switch signals up to 120 V AC or 24 V DC and currents up to 2 A. SB Components 21376
4-channel module with relays designed to work with the Raspberry Pi Pico. It can switch signals up to 250 V AC and 7 A or 30 V DC and 10 A. SB Components 21178
No product available!
Universal board equipped with a metalized hole grid with a pitch of 2.54 mm, enabling mounting using goldpin strips or directly on the surface, with markings facilitating the identification of signals
The PMSA003 air quality sensor module to work with the Raspberry Pi Pico. It allows for a analysis of the amount of pollutants in the environment based on the concentration of PM1.0, PM2.5 and PM10 particles. SB Components 21819
A module with a barcode and QR scanner designed to work with the Raspberry Pi Pico. It allows you to read one-dimensional and two-dimensional codes using the intelligent image recognition algorithm. SB Components 22441
Module with BME688 chip and BH1745 color and light intensity sensor equipped with Raspberry Pi Pico W. Pimoroni PIM630
Module with environmental sensors for Raspberry Pi Pico. It allows you to measure temperature, humidity, air quality pressure and color detection. SB Components 22366
Expansion module designed for Raspberry Pi Pico boards. Allows you to add CAN bus based communication to your project. Waveshare Pico-CAN-B
No product available!
Kit for controlling soil moisture of cultivated plants. Equipped with a Raspberry Pi Pico W-based controller and soil moisture sensors with wires. Pimoroni PIM627
No product available!
Module with BME688 chip, microphone and LTR-559 light intensity. Equipped with a display, it is dedicated to the Raspberry Pi Pico/Pico W. Pimoroni PIM635
2-channel module with relays designed to work with the Raspberry Pi Pico. It can switch signals up to 250 V AC and 7 A or 30 V DC and 10 A. SB Components 21284
No product available!
The KamodRPI Pico Safe Relay is an add-on board for Raspberry Pi Pico featuring four SPDT relays with galvanic isolation, optoisolated digital inputs, and LEDs indicating input and output states. The module is ideal for applications in building automation, robotics, and education, powered via micro USB or USB-C with automatic source selection.
Module with PMSA003 air quality sensor and BME280 pressure sensor designed for Raspberry Pi Pico. It is equipped with WiFi ESP8266 communication. SB Components 22342
Module with a differential pressure sensor based on the MPXV5010DP system. It uses a 22-bit ADC and allows the measurement of the pressure difference between two inlets in the range of up to 10 kPa. Comes with a soldered Raspberry Pi Pico W board. SB Components 26173
Module with a 2-channel driver for DC motors L293D designed to work with the Raspberry Pi Pico. It can work with a voltage from 6 to 12 V and a current of up to 600 mA. SB Components 21468