DC Motor + Stepper FeatherWing - DC and stepper motor controller

An expansion board for Feather boards, featuring a 1.3-inch 128x64 monochrome OLED display and three user buttons. The board comes fully assembled and communicates via I2C, allowing for easy connection to other STEMMA QT devices. The SH1107 display provides high contrast with low power consumption, and a built-in reset button allows for quick system restarts. Adafruit 6313

These add-ons for any Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900 MHz to the Internet or your mobile device. Adafruit 3232

This module enables the Feather series range to be expanded with 8 12-bit PWM outputs that can be used, for example, to control servos or LED diodes. Adafruit 2928

Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650

The adapter allows the Teensy 3.x family to be similar to the Feather family tiles. Thanks to this, it is possible to use a wide range of extensions for Feather tiles. Adafruit 3200

Module with a matrix LED RGB 6x12 display (72 LEDs) designed to work with Feather plates. It communicates via a two-wire SPI interface. Adafruit 3449

An extension that allows you to connect classic 3.5" and 5.25" floppy drives to Feather boards, allowing you to read and write data using the original interface. A built-in logic level converter ensures safe operation with 5V devices, and compatibility with the Feather M4 and RP2040 ensures adequate performance when streaming data. Adafruit 5679

This is the FeatherWing OLED: it adds a 128x32 monochrome OLED plus 3 user buttons to any Feather main board. Using our Feather Stacking Headers or Feather Female Headers you can connect a FeatherWing on top of your Feather board and let the board take flight. Adafruit 2900

The expansion module (shield) is designed for Feather nRF52840 boards. It enables easy connection of 16x32, 32x32 and 64x32 matrix displays. Requires self-assembly. Adafruit 4702

Module with 3-axis accelerometer ADXL343 and precise temperature sensor ADT7410 dedicated to Feather series boards. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4147

Module with a GPS receiver based on the MTK3333 system. Dedicated to Feather plates, communicates via the UART interface. Adafruit 3133

Cap for use with shallow Feather series, with radio module RFM95W 900MHz. It offers a range of up to 2 kilometers (the range can be increased by using an external antenna). It has a SPI interface. Adafruit 3231

This compact development board allows direct connection to 24-pin e-paper displays, ideal for energy-efficient visual projects. Equipped with a 133MHz RP2040 microcontroller, 264KB SRAM, and 8MB Flash, it offers smooth display caching and support for a wide range of peripherals. It features a dedicated SPI display interface, a STEMMA QT connector, a Li-Po charger, USB-C, and a comprehensive GPIO set with PWM, ADC, and I2C, SPI, and UART communication. Adafruit 5727

Feather board will let you integrate packetized radio (with the RFM69 radio) or LoRa radio (with the RFM9x\'s). These radios are good options for kilometer-range radio, and paired with one of our WiFi, cellular or Bluetooth Feathers, will let you bridge from 433/900MHz to the Internet or your mobile device. Adafruit 3230

7-segment display controller, allowing communication over the I2C bus. Allows you to limit the pins needed to control the display. Adafruit 3088

Gamepad module (game controller) with joystick and buttons. Designed for Feather tiles. Adafruit 3632