Adafruit FeatherWing - I2C controller for 7-segment display

Pin expander designed for Feather plates. It is equipped with three sets of female strips and holes for prototyping. Adafruit 3417

Module with a matrix LED RGB 6x12 display (72 LEDs) designed to work with Feather plates. It communicates via a two-wire SPI interface. Adafruit 3449

Gamepad module (game controller) with joystick and buttons. Designed for Feather tiles. Adafruit 3632

Module with a current and voltage sensor dedicated to Feather boards. Can measure voltage up to 26 V and current up to 3.2 A. Based on INA219 sensor, I2C communication. Adafruit 3650

Extension module dedicated to matrix displays with HUB75 interface. Designed for Feather RP2040, M0 and M4 series tiles. Adafruit 3036

The Qwiic connector overlay provides an easy-to-install way to add Qwiic connectors to Thing Plus and Feather boards. Communication takes place via the I2C interface. Sparkfun DEV-16790

Module with 9-axis IMU LSM9DS1 system dedicated to ESP Thing board. Equipped with a connector for connecting GPS and a microSD slot. SparkFun DEV-14430

OLED display with a diagonal of 1.3" and a resolution of 128x64 pixels. Designed for use with Feather series plates. Adafruit 4650

The expansion module (shield) is designed for Feather nRF52840 boards. It enables easy connection of 16x32, 32x32 and 64x32 matrix displays. Requires self-assembly. Adafruit 4702

Data logger dedicated to Thing Plus tiles. It allows you to save data on a microSD card with the possibility of reading through the USB port. Supports cards up to 32 GB. SparkFun DEV-19217

CAN controller module for Feather boards. It features an MCP2515 CAN controller and a TJA1051 transceiver and allows data transfer at speeds of up to 1Mb/s. Adafruit 5709

Module with 3-axis accelerometer ADXL343 and precise temperature sensor ADT7410 dedicated to Feather series boards. Equipped with a STEMMA QT connector, it communicates via the I2C interface. Adafruit 4147

The compact enclosure for the Adafruit Feather RP2040 with DVI output is printed using SLA technology in semi-transparent plastic, providing protection and visibility of the LED indicators. It allows easy access to all ports and buttons, and the snap-in design eliminates the need for screws or glue. Adafruit 6241

This expansion board is designed for light and sound, cosplay, and interactive prop projects. It features a ready-made NeoPixel port with a level converter, 3W RGB LED drivers, and a Class D audio amplifier for driving 8Ω or 4Ω speakers. The built-in LIS3DH accelerometer allows for motion, impact, and tilt detection, ideal for dynamic effects. It works with a wide range of Feather boards, allowing you to quickly create advanced projects in a compact format. Adafruit 3988

This compact development board allows direct connection to 24-pin e-paper displays, ideal for energy-efficient visual projects. Equipped with a 133MHz RP2040 microcontroller, 264KB SRAM, and 8MB Flash, it offers smooth display caching and support for a wide range of peripherals. It features a dedicated SPI display interface, a STEMMA QT connector, a Li-Po charger, USB-C, and a comprehensive GPIO set with PWM, ADC, and I2C, SPI, and UART communication. Adafruit 5727

An expansion board for Feather boards, featuring a 1.3-inch 128x64 monochrome OLED display and three user buttons. The board comes fully assembled and communicates via I2C, allowing for easy connection to other STEMMA QT devices. The SH1107 display provides high contrast with low power consumption, and a built-in reset button allows for quick system restarts. Adafruit 6313